Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

intervlan routing 3560g

Hi all!

I have 3560g with EMI. I connect my PC to GEth0/3 3560g and create SVI with address x.x.x.209 255.255.255.240, on my PC address is x.x.x.210 255.255.255.240. I add Linksys SRW224G4 to GEth0/2 port 3560g. I have trunk between 3560g and Linksys. Linksys has management vlan 553 and 10.0.77.70/27 address in this vlan. I create SVI (vlan 553) on 3560g with address 10.0.77.65 255.255.255.224. Linksys has default-gateway 10.0.77.65.

3560G:

...

!

ip routing

...

!

interface Vlan201

ip address x.x.x.209 255.255.255.240

...

!

interface Vlan553

ip address 10.0.77.65 255.255.255.224

#sh ip route | i 10.0.77

C 10.0.77.64/27 is directly connected, Vlan553

#sh ip route | i x.x.x

x.x.x.0/28 is subnetted, 1 subnets

C x.x.x.208 is directly connected, Vlan201

I can ping 10.0.77.65 from my PC and I can ping x.x.x.209 from Linksys, but I can't ping 10.0.77.70 (Linksys) from my PC and I can't ping x.x.x.210 (PC) from Linksys.

I enable debug ip icmp packet, when I ping Linksys from PC or I ping PC from Linksys I'm not see anything. When I ping 10.0.77.65 from PC I see rows with echo requests and echo replies. I see is similar for Linksys.

What is problem may be?

17 REPLIES
Hall of Fame Super Bronze

Re: intervlan routing 3560g

Assign a port membership on G0/3 for Vlan 201

switchport mode access

switchport access vlan 201

and G0/2 should be assigned to 553

switchport mode access

switchport access vlan 553

I haven't played around with that LinkSys model but I think you are having problems with the trunk. You don't need a trunk for this configuration to work.

New Member

Re: intervlan routing 3560g

!

interface GigabitEthernet0/2

description ###LinkSYS###

switchport trunk encapsulation dot1q

switchport mode trunk

...

!

interface GigabitEthernet 0/3

description ###PC###

no switchport

ip address x.x.x.209 255.255.255.240

These interfaces has already configured. I want use trunk, because I want connect clients to Linksys.

Silver

Re: intervlan routing 3560g

Hi Zakini ,

I would like to know few things..

1.you have configured same ip on 3560g on two interfaces ..i.e

interface Vlan201

ip address x.x.x.209 255.255.255.240

and

interface GigabitEthernet 0/3

description ###PC###

no switchport

ip address x.x.x.209 255.255.255.240

how come it is possible.

have you got any message saying that ip conflict or host flapping on 3560g switch...

assign different ip subnet on g0/3 and do the routing on linksys switch and check the issue...

Thanks,

satish

New Member

Re: intervlan routing 3560g

Sorry, I mistake, I try two ways. Now config is:

!

ip routing

...

!

interface GigabitEthernet0/2

description ###LinkSYS###

switchport trunk encapsulation dot1q

switchport mode trunk

!

interface GigabitEthernet 0/3

description ###PC###

no switchport

ip address x.x.x.209 255.255.255.240

...

!

interface Vlan553

ip address 10.0.77.65 255.255.255.224

#sh ip route | i 10.0.77

C 10.0.77.64/27 is directly connected, Vlan553

#sh ip route | i x.x.x

x.x.x.0/28 is subnetted, 1 subnets

C x.x.x.208 is directly connected, GigabitEthernet0/3

I'm not have ping from PC to LinkSYS

Silver

Re: intervlan routing 3560g

Hi ,

Then configuration on routers must be like ...

ip routing

interface g0/3

no switchport

ip address x.x.x.209 255.255.255.240

...

interface Vlan553

ip address 10.0.77.65 255.255.255.224

Pc ip's :

x.x.x.210 255.255.255.240.

gateway x.x.x.209

ip route 0.0.0.0 0.0.0.0 10.0.77.66

configure default route on linksys switch

ip route 0.0.0.0 0.0.0.0 10.0.77.65.

Check the issue...

Thanks,

satish

New Member

Re: intervlan routing 3560g

Ok, but I'm not have ping Linksys from PC

Silver

Re: intervlan routing 3560g

Hi ,

have you configured default route on both the switches ..

why did you configure g0/3 as a routing port..

have yoy tried same thing by configuring vlan x with x.x.x.209 ip addrress...by removing x.x.x.209 from g0/3 interface.

g0/3 --- switchport mode access

switchport access vlan x.

and assign one port of 3560g in vlan x and

try to ping to linksys switch.

Thanks,

satish

allow these two vlans through trunk.

Thanks,

satish

New Member

Re: intervlan routing 3560g

Hi!

I have default route on Linksys and my PC has static route to network Linksys. I can ping from PC to gateway of network linksys.

I change my config:

!

ip routing

...

!

interface GigabitEthernet0/2

description ###Linksys###

switchport trunk encapsulation dot1q

switchport mode trunk

!

interface GigabitEthernet0/3

switchport access vlan 201

switchport mode access

!

...

!

interface Vlan201

ip address x.x.x.209 255.255.255.240

...

!

interface Vlan553

ip address 10.0.77.65 255.255.255.224

I'm not have ping from PC to Linksys

Hall of Fame Super Bronze

Re: intervlan routing 3560g

Can you please configure the switchports as suggested ?

_________________

Assign a port membership on G0/3 for Vlan 201

switchport mode access

switchport access vlan 201

and G0/2 should be assigned to 553

switchport mode access

switchport access vlan 553

___________________

The Linksys may be having problems with the trunk configuration and actually, you don't need a trunk port (LinkSys isn't holding more than one Vlan).

On an invalid trunk configuration on the Cisco switch, it may be default back to native vlan 1 which is not the desired vlan on this case.

New Member

Re: intervlan routing 3560g

My config

!

ip routing

...

!

interface GigabitEthernet0/2

description ###Linksys###

switchport trunk encapsulation dot1q

switchport mode trunk

!

interface GigabitEthernet0/3

switchport access vlan 201

switchport mode access

!

...

!

interface Vlan201

ip address x.x.x.209 255.255.255.240

...

!

interface Vlan553

ip address 10.0.77.65 255.255.255.224

I ping from PC to Linksys. I enable span session and analyze packets. I see echo requests from pc and echo replies from linksys on gigabitethernet 0/2 (Linksys), but I'm not see echo replies from Linksys on port connected to my PC...

Hall of Fame Super Bronze

Re: intervlan routing 3560g

One more time ... Please change the interface g0/2 to access mode.

interface GigabitEthernet0/2

description ###Linksys###

switchport access vlan 553

switchport mode access

New Member

Re: intervlan routing 3560g

Interface vlan 553 is state to down when I changed the gigabitethernet0/2 to mode access. I see tag 553 in packet echo reply from linksys. I think the trunk work is fine.

Hall of Fame Super Bronze

Re: intervlan routing 3560g

Again, you don't need a trunk configuration between these 2 link partners. You aren't carrying more than one Vlan so please don't complicate things.

If the linksys was configure for trunking, please change it.

When you changed the g0/2 to access, did you assign it to vlan 553 as well ?

Can I see the output from typing

show interface g0/2 and show vlan after making the changes I suggested ?

New Member

Re: intervlan routing 3560g

New config:

...

!

ip routing

!

...

!

interface GigabitEthernet0/2

description ###LINKSYS###

switchport access vlan 553

switchport mode access

!

interface GigabitEthernet0/3

description ###PC###

switchport access vlan 201

switchport mode access

...

!

interface Vlan201

ip address x.x.x.209 255.255.255.240

...

!

interface Vlan553

ip address 10.0.77.65 255.255.255.224

sh int gigabitEthernet 0/2

GigabitEthernet0/2 is up, line protocol is up (connected)

Hardware is Gigabit Ethernet, address is 001a.a2ac.db02 (bia 001a.a2ac.db02)

Description: ###LINKSYS###

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

Keepalive set (10 sec)

Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX

input flow-control is off, output flow-control is unsupported

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:00:22, output 00:00:04, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

193 packets input, 28798 bytes, 0 no buffer

Received 41 broadcasts (0 multicast)

0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 watchdog, 35 multicast, 0 pause input

0 input packets with dribble condition detected

386 packets output, 30374 bytes, 0 underruns

0 output errors, 0 collisions, 1 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier, 0 PAUSE output

0 output buffer failures, 0 output buffers swapped out

sh int vlan 553

Vlan553 is up, line protocol is up

Hardware is EtherSVI, address is 001a.a2ac.db7f (bia 001a.a2ac.db7f)

Internet address is 10.0.77.65/27

MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

ARP type: ARPA, ARP Timeout 04:00:00

Last input 00:02:21, output 00:00:00, output hang never

Last clearing of "show interface" counters never

Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

Queueing strategy: fifo

Output queue: 0/40 (size/max)

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

152 packets input, 20218 bytes, 0 no buffer

Received 0 broadcasts (0 IP multicast)

0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

327 packets output, 22578 bytes, 0 underruns

0 output errors, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

I ping successfull Linksys from PC after changed my config.

Hall of Fame Super Bronze

Re: intervlan routing 3560g

Great !

New Member

Re: intervlan routing 3560g

yes, thanks.

I'm disturb because I want using linksys with trunk to catalyst..

Hall of Fame Super Bronze

Re: intervlan routing 3560g

Why would you need a trunk if you are only carrying a single Vlan over this link ?

248
Views
0
Helpful
17
Replies
CreatePlease to create content