Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

link of ports going up and down on 1 single blade

Hello everyone, we have been experiencing some weird problem over the past few days and wanted to get some input from the community,

Monday morning, we started have been experiencing some rolling black outs on blade 4 of our 6506. Users are calling in and reporting that they were momentarily discommended form the network. Sure enough, if we go to the computer, can see in the system event logs event ID generated by the NIC (Broadcom NetXtreme 57xx Gigabit Controller: The network link is down. Check to make sure the network cable is properly connected.) Moments later, the following message will be written to the event logs (Broadcom NetXtreme 57xx Gigabit Controller: Network controller configured for 100Mb full-duplex link.)

A few hours after the first reports, our supervisor engine crashed and rebooted.

Since we have moved every user attached to blade 4 and moved them to access switches and free ports on other blades.

After receiving a replacement SUP on Tuesday, we have slowly started to move users back onto blade 4 and we are still experiencing some port disconnecting.

At this point, I should we replace the blade?

Here is a show modules outputs

Show Modules

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2 SAL0847671B

3 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 SAL044415G2

4 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 SAL0506377M

5 48 48 port 10/100 mb RJ45 WS-X6348-RJ-45 SAD04170D7X

6 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX SAL094865L4

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0006.d65e.e79c to 0006.d65e.e79d 5.1 7.1(1) 12.1(27b)E3 Ok

3 0003.6c12.5a10 to 0003.6c12.5a3f 2.2 5.4(2) 8.5(0.23)COS Ok

4 0004.de80.ea00 to 0004.de80.ea2f 1.7 5.4(2) 8.5(0.23)COS Ok

5 0001.9714.fd40 to 0001.9714.fd6f 1.1 5.3(1) 8.5(0.23)COS Ok

6 0015.fa60.5f3c to 0015.fa60.5f6b 1.1 7.2(1) 8.5(0.23)COS Ok

Mod Sub-Module Model Serial Hw Status

--- --------------------------- --------------- --------------- ------- -------

1 Policy Feature Card 2 WS-F6K-PFC2 SAL08455WFU 3.5 Ok

1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL08465YDE 2.8 Ok

Mod Online Diag Status

--- -------------------

1 Pass

3 Pass

4 Pass

5 Pass

6 Pass

2 REPLIES

Re: link of ports going up and down on 1 single blade

Daniel,

1) do you get any console messages when this happens?

2) If you have configured syslog, can you check those syslog messages?

Personally, if i were you, I would again talk to the cisco accounts representative and/or open a TAC Case to find the root cause.

New Member

Re: link of ports going up and down on 1 single blade

Thanks for your post. I have a crash details but no syslog.

I will configure syslog now and gather more details.

123
Views
4
Helpful
2
Replies