Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

MAC addresses aren't appear on the port.

I have a problem.

When I connect somethings to ports such as a pc, a sever, a swich and a router, their MAC address are not appear on the ports.

As a matter of course, I adjusted the speed and duplex each other.

Empty ports have the same problem without used ports.

What should I do ?

===================================================================================

RT#sh mac-address-table interface fastEthernet 13/1

Legend: * - primary entry

age - seconds since last seen

n/a - not available

vlan mac address type learn age ports

------+----------------+--------+-----+----------+--------------------------

No entries present.

RT#show interface status module 13

Port Name Status Vlan Duplex Speed Type

Fa13/1 connected 100 full 100 10/100BaseTX

====================================================================================

ㅁ Version : s72033-entservicesk9_wan-mz.122-18.SXF8.bin

ㅁ show module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

5 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL08455RLA

6 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL1115LP4P

7 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL10478LAW

8 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAD090309SJ

9 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAD04220BGF

10 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL082804QJ

11 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SAL0812333C

12 48 48 port 10/100 mb RJ-45 ethernet WS-X6248-RJ-45 SAD040309TS

13 48 48-port 10/100 mb RJ45 WS-X6148-RJ-45 SAL0912664E

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

7 Policy Feature Card 3 WS-F6K-PFC3B SAL10478P56 2.3 Ok

7 MSFC3 Daughterboard WS-SUP720 SAL10478LGN 2.5 Ok

8 Policy Feature Card 3 WS-F6K-PFC3B SAD09030BCL 1.1 Ok

8 MSFC3 Daughterboard WS-SUP720 SAD090201ZP 2.2 Ok

3 REPLIES
Silver

Re: MAC addresses aren't appear on the port.

- Are you having the same problem is you connect one of those PCs to a port on the WS-X6248-RJ-45 module?

- Under the show int f13/1, do you see an increasing input packet count? any errors?

- Is the STP state FWD, use sh spann int f13/1 ?

New Member

Re: MAC addresses aren't appear on the port.

Hi, jbrenesj

I am really appreciate your help.

- Are you having the same problem is you connect one of those PCs to a port on the WS-X6248-RJ-45 module?

-> Yes, all empty(notconnect) ports except that ports is already in use by user have the same problem.

- Under the show int f13/1, do you see an increasing input packet count? any errors?

-> Input packet count and any errors are always "0".

- Is the STP state FWD, use sh spann int f13/1 ?

-> The STP state is FWD.

What do you think of this problem ?

New Member

Re: MAC addresses aren't appear on the port.

I didn't mistake your question.

- Under the show int f13/1, do you see an increasing input packet count? any errors?

-> Input packet count is increasing but I don't know the packet.

111
Views
0
Helpful
3
Replies