Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

MTU

Hi,

Is there a difference between interface MTU and IP MTU ?

Thanks, birdy

2 ACCEPTED SOLUTIONS

Accepted Solutions
New Member

Re: MTU

Hi,

you can use the command lookup tool to solve your problem ;)

ip mtu (source: command lookup tool)

To set the maximum transmission unit (MTU) size of IP packets sent on an interface, use the ip mtu command in interface configuration mode. To restore the default MTU size, use the no form of this command.

ip mtu bytes

no ip mtu

Syntax Description

bytes

MTU in bytes.

Defaults

Minimum is 128 bytes; maximum depends on the interface medium.

Command Modes

Interface configuration (config-if)

Command History

Release Modification

10.0

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Usage Guidelines

If an IP packet exceeds the MTU set for the interface, the Cisco IOS software will fragment it.

All devices on a physical medium must have the same protocol MTU in order to operate.

Greetz from Germany ;)

Super Bronze

Re: MTU

Yes, they are different. IP MTU only applies to IP packets.

"Note Changing the MTU value (with the mtu interface configuration command) can affect the IP MTU value. If the current IP MTU value is the same as the MTU value, and you change the MTU value, the IP MTU value will be modified automatically to match the new MTU. However, the reverse is not true; changing the IP MTU value has no effect on the value for the mtu command."

5 REPLIES
New Member

Re: MTU

HI

The hardware MTU configured with the mtu interface configuration command

The IP MTU configured with the ip mtu interface configuration command

The MPLS MTU configured with the mpls mtu interface configuration command

Hope this help

New Member

Re: MTU

Hi,

Thanks for yr reply.

I am not refering to the command but is asking what is the difference between IP MTU and interface MTU ?

Is the IP MTU size always the same as the interface MTU size ?

Regards

New Member

Re: MTU

Hi,

you can use the command lookup tool to solve your problem ;)

ip mtu (source: command lookup tool)

To set the maximum transmission unit (MTU) size of IP packets sent on an interface, use the ip mtu command in interface configuration mode. To restore the default MTU size, use the no form of this command.

ip mtu bytes

no ip mtu

Syntax Description

bytes

MTU in bytes.

Defaults

Minimum is 128 bytes; maximum depends on the interface medium.

Command Modes

Interface configuration (config-if)

Command History

Release Modification

10.0

This command was introduced.

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Usage Guidelines

If an IP packet exceeds the MTU set for the interface, the Cisco IOS software will fragment it.

All devices on a physical medium must have the same protocol MTU in order to operate.

Greetz from Germany ;)

Super Bronze

Re: MTU

Yes, they are different. IP MTU only applies to IP packets.

"Note Changing the MTU value (with the mtu interface configuration command) can affect the IP MTU value. If the current IP MTU value is the same as the MTU value, and you change the MTU value, the IP MTU value will be modified automatically to match the new MTU. However, the reverse is not true; changing the IP MTU value has no effect on the value for the mtu command."

New Member

Re: MTU

Hi All,

Thanks for your explanation.

Now it is much clearer.

Thanks again

birdy

350
Views
2
Helpful
5
Replies
CreatePlease to create content