Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Multicast issue and help needed

I have configured multicast between two sites running two Cisco 2600 router over T1 and Cisco 2948 switches behind them. I'm runing weblogic multicast with the TTL of 2 or higher. I see multicast on one end but the other end shows nothing.

My interface config look like this

interface FastEthernet0/0.3

encapsulation dot1Q 103

ip address 192.168.216.1 255.255.255.128

ip pim sparse-dense-mode

no ip route-cache

no ip mroute-cache

My other end is .129/25 and I have cgmp enabled on Cisco 2948.

Is there anything I'm missing in the configuration? Please advice.

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: Multicast issue and help needed

Silly question but have you configured PIM on the serail link between the two sites?

Harold Ritter
Sr. Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México 
Paseo de la Reforma 222 Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México
4 REPLIES
Cisco Employee

Re: Multicast issue and help needed

It is hard to comment with so little info. Did you configure a static RP or auto-RP? Can you attach the output of a show ip mroute" from the router ar the site that doesn't receive the multicast packets.

Cheers,

Harold Ritter
Sr. Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México 
Paseo de la Reforma 222 Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México
New Member

Re: Multicast issue and help needed

Yes

Non Working router:--

Exec-2620-HB#sh ip mroute

IP Multicast Routing Table

Flags: D - Dense, S - Sparse, C - Connected, L - Local, P - Pruned

R - RP-bit set, F - Register flag, T - SPT-bit set, J - Join SPT

M - MSDP created entry, X - Proxy Join Timer Running

A - Candidate for MSDP Advertisement

Outgoing interface flags: H - Hardware switched

Timers: Uptime/Expires

Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 224.0.1.40), 1d00h/00:00:00, RP 0.0.0.0, flags: DJCL

Incoming interface: Null, RPF nbr 0.0.0.0

Outgoing interface list:

FastEthernet0/0.3, Forward/Sparse-Dense, 1d00h/00:00:00

Working Router:--

dc-3620-Hb#sh ip mroute

IP Multicast Routing Table

Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,

L - Local, P - Pruned, R - RP-bit set, F - Register flag,

T - SPT-bit set, J - Join SPT, M - MSDP created entry,

X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,

U - URD, I - Received Source Specific Host Report

Outgoing interface flags: H - Hardware switched

Timers: Uptime/Expires

Interface state: Interface, Next-Hop or VCD, State/Mode

(*, 237.0.0.96), 20:52:57/00:02:59, RP 0.0.0.0, flags: DC

Incoming interface: Null, RPF nbr 0.0.0.0

Outgoing interface list:

FastEthernet0/0.3, Forward/Sparse-Dense, 20:52:57/00:00:00

(192.168.216.4, 237.0.0.96), 00:02:59/00:00:00, flags: PCT

Incoming interface: FastEthernet0/0.3, RPF nbr 0.0.0.0

Outgoing interface list: Null

(192.168.216.5, 237.0.0.96), 00:00:39/00:02:20, flags: PCT

Incoming interface: FastEthernet0/0.3, RPF nbr 0.0.0.0

Outgoing interface list: Null

(*, 224.0.1.40), 1d00h/00:00:00, RP 0.0.0.0, flags: DCL

Incoming interface: Null, RPF nbr 0.0.0.0

Outgoing interface list:

FastEthernet0/0.3, Forward/Sparse-Dense, 1d00h/00:00:0

Cisco Employee

Re: Multicast issue and help needed

Silly question but have you configured PIM on the serail link between the two sites?

Harold Ritter
Sr. Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México 
Paseo de la Reforma 222 Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México
New Member

Re: Multicast issue and help needed

Not a silly question because this is something I missed. It now works when enabled on serial interface. Thanks a lot

229
Views
0
Helpful
4
Replies