Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

multicast on 3560X

I'v got a 3560X switch

#sh ver

Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9NPE-M), Version 15.0(2)SE2, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Tue 05-Feb-13 12:08 by prod_rel_team

ROM: Bootstrap program is C3560E boot loader

BOOTLDR: C3560E Boot Loader (C3560X-HBOOT-M) Version 12.2(53r)SE2, RELEASE SOFTWARE (fc1)

uptime is 4 days, 5 hours, 53 minutes

System returned to ROM by power-on

System restarted at 06:33:32 MSK Fri Aug 30 2013

System image file is "flash:/c3560e-universalk9npe-mz.150-2.SE2.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

License Level: ipbase

License Type: Permanent

Next reload license Level: ipbase

cisco WS-C3560X-48P (PowerPC405) processor (revision K0) with 262144K bytes of memory.

Processor board ID FDO1703H3A9

Last reset from power-on

3 Virtual Ethernet interfaces

1 FastEthernet interface

52 Gigabit Ethernet interfaces

2 Ten Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address       : 4C:4E:35:31:D1:80

Motherboard assembly number     : 73-12557-08

Motherboard serial number       : FDO17040946

Model revision number           : K0

Motherboard revision number     : A0

Model number                    : WS-C3560X-48P-S

Daughterboard assembly number   : 800-32786-02

Daughterboard serial number     : FDO17032XP4

System serial number            : FDO1703H3A9

Top Assembly Part Number        : 800-31328-07

Top Assembly Revision Number    : B0

Version ID                      : V04

CLEI Code Number                : COMJP00ARD

Hardware Board Revision Number  : 0x04

Switch Ports Model              SW Version            SW Image

------ ----- -----              ----------            ----------

*    1 54    WS-C3560X-48P      15.0(2)SE2            C3560E-UNIVERSALK9NPE-M

Configuration register is 0xF

When I try to enable pim on interface, there is no commands(ip pim sparse/dance) on inteface level

#sh run | i multi

ip multicast-routing distributed

#conf t

Enter configuration commands, one per line.  End with CNTL/Z.

(config)#int vlan 84

(config-if)#ip pim ?

  passive  Enable PIM passive interface operation

(config-if)#ip pim

Why it happens? Thanks

1 REPLY
Cisco Employee

multicast on 3560X

Hi,

You are currently running the IPBASE license. You need a higher license, e.g. IPSERVICES, to run full multicast routing. Currently, your multilayer switch supports only what is called PIM Stub Routing which is a strongly scaled-down capability of PIM participation, and is suitable only for routed access layer deployments.

Best regards,

Peter

234
Views
0
Helpful
1
Replies