Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Need SSO help - Sup7203b's

Well I have been back and forth on this awhile now...I have a 6513E chassis that is getting prepped for prod.

I am currently testing sso functionality and I can only get it to work using the following images

on both Sup Cards

s72033-adventerprise_wan-mz.122-33.SXI5.bin

If I try any other image, smaller or bigger in size...it forces my Sup card in mod 8 to recycle " proxy request from peer "

I have tried K9 images and non K9 images.

Here is an output from sh redundancy

Redundant System Information :
------------------------------
       Available system uptime = 4 minutes
Switchovers system experienced = 0
              Standby failures = 0
        Last switchover reason = none

                 Hardware Mode = Duplex
    Configured Redundancy Mode = sso
     Operating Redundancy Mode = sso
              Maintenance Mode = Disabled
                Communications = Up

Current Processor Information :
-------------------------------
               Active Location = slot 7
        Current Software state = ACTIVE
       Uptime in current state = 3 minutes
                 Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISE_WAN-M), Version 12.2(33)SXI5, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Sat 23-Oct-10 01:29 by prod_rel_team
                          BOOT = disk0:s72033-adventerprise_wan-mz.122-33.SXI5.bin,1;
                   CONFIG_FILE =
                       BOOTLDR = bootflash:
        Configuration register = 0x2102

Peer Processor Information :
----------------------------
              Standby Location = slot 8
        Current Software state = STANDBY HOT
       Uptime in current state = 0 minutes
                 Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISE_WAN-M), Version 12.2(33)SXI5, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Sat 23-Oct-10 01:29 by prod_rel_team
                          BOOT = disk0:s72033-adventerprise_wan-mz.12.2-(33)SXI5.bin,12;
                   CONFIG_FILE =
                       BOOTLDR = bootflash:
        Configuration register = 0x2102

Heres a sh mod

Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL13410GF9
  3   48  SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX     SAD074003KU
  7    2  Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL13431ZWK
  8    2  Supervisor Engine 720 (Hot)            WS-SUP720-3B       SAL09306D4F
10    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      SAL1448197E
11   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL1431PFV8

Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  1  0027.0d35.a270 to 0027.0d35.a287   4.1   12.2(18r)S1  12.2(33)SXI5 Ok
  3  000d.29f6.9880 to 000d.29f6.98af   5.0   7.2(1)       12.2(33)SXI5 Ok
  7  001f.6c77.7670 to 001f.6c77.7673   5.9   8.5(3)       12.2(33)SXI5 Ok
  8  0013.c42e.7168 to 0013.c42e.716b   4.4   8.5(2)       12.2(33)SXI5 Ok
10  1cdf.0f84.3d10 to 1cdf.0f84.3d13   3.2   12.2(14r)S5  12.2(33)SXI5 Ok
11  d0d0.fd64.aeb8 to d0d0.fd64.aee7   3.4   12.2(18r)S1  12.2(33)SXI5 Ok

Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
  1  Centralized Forwarding Card WS-F6700-CFC       SAL134324T6  4.1    Ok
  7  Policy Feature Card 3       WS-F6K-PFC3B       SAL13421NL5  2.6    Ok
  7  MSFC3 Daughterboard         WS-SUP720          SAL13421LZ8  4.0    Ok
  8  Policy Feature Card 3       WS-F6K-PFC3B       SAL092963W3  2.1    Ok
  8  MSFC3 Daughterboard         WS-SUP720          SAL09295MWF  2.3    Ok
10  Centralized Forwarding Card WS-F6700-CFC       SAL144816SB  4.1    Ok
11  Centralized Forwarding Card WS-F6700-CFC       SAL1431PB6L  4.1    Ok

Any help would be appreciated.

Cheers


Dave

2 REPLIES
VIP Super Bronze

Need SSO help - Sup7203b's

Dave,

Your SSO redundancy looks fine. The primary is active and the stand-by is HOT. Does it do the same thing, if you switch Sups? (Put the one that reboots in module 7 and the current promary in module 8)

New Member

Need SSO help - Sup7203b's

Yeah with this image, SSO works fine...I havent tried swapping the slots...I'll give that a try.


I noticed that the versions of MSFC3's and PFC3's are different, would that make a difference ?

288
Views
0
Helpful
2
Replies