Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Netflow for 4510R

Trying to collect netflow from a 4510R, but I am not able to. Current software version for 4510R is cat4500-IPBASEK9-M 12.2(40)SG release software (fc2).

The running-config for ip flow...

ip flow-export source GigabitEthernet4/1

ip flow-export version 5

ip flow-export destination 10.x.x.x 2055

And the running-config for the interface gi4/1....

description - BHN-MetroEthernet -

no switchport

ip address 10.zz.0.yy 255.255.255.0

ip pim sparse-mode

ip multicast boundary mcast-boundary-acl

ip summary-address eigrp 1 10.yy.0.0 255.255.0.0 5

power inline never

speed 100

duplex full

qos trust dscp

flowcontrol receive on

What am I missing?

Thanks in advance for the help.

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
Bronze

Netflow for 4510R

With SUP Engine V-10GE, NetFlow fucntionality is embedded. Have you tried configuring as below:

ip flow-export destination 10.x.x.x 2055

ip flow-export source GigabitEthernet4/1 \\ Any interface that can take the NetFlow packets to the server

ip flow-export version 7

ip flow-cache timeout active 1

ip flow ingress layer2-switched

ip flow ingress infer-fields     \\ If your IOS does not support this, use 'ip route-cache flow infer-fields'

Regards,
Don Thomas Jacob
http://www.solarwinds.com/netflow-traffic-analyzer.aspx

NOTE: Please rate and close questions if you found any of the answers helpful.

Regards, Don Thomas Jacob http://www.solarwinds.com/netflow-traffic-analyzer.aspx Head Geek @ SolarWinds NOTE: Please rate and close questions if you found any of the answers helpful.
4 REPLIES
Purple

Netflow for 4510R

  What supervisor do you have?  Do you have a netflow services card installed.  Seeing you have ipbase it probably won't support netflow on that version either. 

New Member

Netflow for 4510R

We have 2 sup module in this chassis, and both are WS-X4516-10GE. Not sure if there is a netflow services card. Will I be able to find that out from CLI? What IO version should I get to get netflow to work?

Thank you for the help.

Bronze

Netflow for 4510R

With SUP Engine V-10GE, NetFlow fucntionality is embedded. Have you tried configuring as below:

ip flow-export destination 10.x.x.x 2055

ip flow-export source GigabitEthernet4/1 \\ Any interface that can take the NetFlow packets to the server

ip flow-export version 7

ip flow-cache timeout active 1

ip flow ingress layer2-switched

ip flow ingress infer-fields     \\ If your IOS does not support this, use 'ip route-cache flow infer-fields'

Regards,
Don Thomas Jacob
http://www.solarwinds.com/netflow-traffic-analyzer.aspx

NOTE: Please rate and close questions if you found any of the answers helpful.

Regards, Don Thomas Jacob http://www.solarwinds.com/netflow-traffic-analyzer.aspx Head Geek @ SolarWinds NOTE: Please rate and close questions if you found any of the answers helpful.
New Member

Netflow for 4510R

It worked, but I have to stay with ip flow-export version 5. BIG THANK YOU!

625
Views
0
Helpful
4
Replies