Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Netflow Monitoring

Hello Community,

I'm in the process of trying to establish why our ATM link is becoming over utilised. The problem is I'm not sure what what interface I should be monitoring.

For example, the output below shows the interface information for  ATM 0/1/0, Dialer 1, Virtual-Access 2, and Tunnel 0.

Can you advice on the interface that I should monitor?

ATM0/1/0 is up, line protocol is up

  Hardware is MPC ATMSAR, address is 6073.5cd8.95a6 (bia 6073.5cd8.95a6)

  Description: Internet Connection

  MTU 1600 bytes, sub MTU 1600, BW 448 Kbit/sec, DLY 820 usec,

     reliability 255/255, txload 10/255, rxload 27/255

  Encapsulation ATM, loopback not set

  Keepalive not supported

  Encapsulation(s): AAL5

  4 maximum active VCs, 1024 VCs per VP, 1 current VCCs

  VC Auto Creation Disabled.

  VC idle disconnect time: 300 seconds

  Last input never, output 00:00:00, output hang never

  Last clearing of "show interface" counters 1d06h

  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 10639

  Queueing strategy: Per VC Queueing

  5 minute input rate 48000 bits/sec, 10 packets/sec

  5 minute output rate 18000 bits/sec, 10 packets/sec

     5719399 packets input, 952942086 bytes, 0 no buffer

     Received 0 broadcasts (0 IP multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

     4993291 packets output, 1672459181 bytes, 0 underruns

     0 output errors, 0 collisions, 0 interface resets

     0 unknown protocol drops

     0 output buffer failures, 0 output buffers swapped out

uk01340-rm01-ald#show int dialer 1

Dialer1 is up, line protocol is up (spoofing)

  Hardware is Unknown

  Internet address is 80.xxx.xxx.xxx/30

  MTU 1500 bytes, BW 56 Kbit/sec, DLY 20000 usec,

     reliability 255/255, txload 1/255, rxload 204/255

  Encapsulation PPP, LCP Closed, loopback not set

  Keepalive set (10 sec)

  DTR is pulsed for 1 seconds on reset

  Interface is bound to Vi2

  Last input never, output never, output hang never

  Last clearing of "show interface" counters 1d06h

  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: weighted fair

  Output queue: 0/1000/64/0 (size/max total/threshold/drops)

     Conversations  0/0/16 (active/max active/max total)

     Reserved Conversations 0/0 (allocated/max allocated)

     Available Bandwidth 42 kilobits/sec

  5 minute input rate 45000 bits/sec, 8 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     5708860 packets input, 929602766 bytes

     5004084 packets output, 1676830477 bytes

Bound to:

Virtual-Access2 is up, line protocol is up

  Hardware is Virtual Access interface

  MTU 1500 bytes, BW 448 Kbit/sec, DLY 20000 usec,

     reliability 255/255, txload 9/255, rxload 25/255

  Encapsulation PPP, LCP Open

  Open: IPCP

  PPPoATM vaccess, cloned from Dialer1

  Vaccess status 0x44

  Bound to ATM0/1/0 VCD: 1, VPI: 0, VCI: 38, loopback not set

  Keepalive set (10 sec)

  DTR is pulsed for 5 seconds on reset

  Interface is bound to Di1 (Encapsulation PPP)

  Last input 00:00:00, output never, output hang never

  Last clearing of "show interface" counters 1d06h

  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 45000 bits/sec, 9 packets/sec

  5 minute output rate 17000 bits/sec, 9 packets/sec

     5719524 packets input, 930220408 bytes, 0 no buffer

     Received 0 broadcasts (0 IP multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

     5004088 packets output, 1676831301 bytes, 0 underruns

     0 output errors, 0 collisions, 0 interface resets

     0 unknown protocol drops

     0 output buffer failures, 0 output buffers swapped out

     0 carrier transitions

uk01340-rm01-ald#show interfaces tunnel 0

Tunnel0 is up, line protocol is up

  Hardware is Tunnel

  Description: ** mGRE/NHRP tunnel **

  Internet address is 172.17.142.121/24

  MTU 17912 bytes, BW 2048 Kbit/sec, DLY 50000 usec,

     reliability 255/255, txload 1/255, rxload 5/255

  Encapsulation TUNNEL, loopback not set

  Keepalive not set

  Tunnel source 80.xxx.xxx.xxx (Dialer1)

   Tunnel Subblocks:

      src-track:

         Tunnel0 source tracking subblock associated with Dialer1

          Set of tunnels with source Dialer1, 1 member (includes iterators), on interface <OK>

  Tunnel protocol/transport multi-GRE/IP

    Key 0x30D42, sequencing disabled

    Checksumming of packets disabled

  Tunnel TTL 255, Fast tunneling enabled

  Tunnel transport MTU 1472 bytes

  Tunnel transmit bandwidth 8000 (kbps)

  Tunnel receive bandwidth 8000 (kbps)

  Tunnel protection via IPSec (profile "vpnprofile")

  Last input 00:00:00, output never, output hang never

  Last clearing of "show interface" counters 1d06h

  Input queue: 0/256/0/0 (size/max/drops/flushes); Total output drops: 21327

  Queueing strategy: fifo

  Output queue: 0/0 (size/max)

  5 minute input rate 48000 bits/sec, 2 packets/sec

  5 minute output rate 5000 bits/sec, 3 packets/sec

     5694230 packets input, 500481747 bytes, 0 no buffer

     Received 0 broadcasts (0 IP multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

     4967869 packets output, 1658929974 bytes, 0 underruns

     0 output errors, 0 collisions, 0 interface resets

     0 unknown protocol drops

     0 output buffer failures, 0 output buffers swapped out

uk01340-rm01-ald#

Thanks it advance for you help?

Cheers

Carlton

  • LAN Switching and Routing
1 REPLY

Netflow Monitoring

You do not have any Net Flow monitoring system in place because that should be able to give you stats on which interface and who is utilizing it doing what etc. 

148
Views
0
Helpful
1
Replies
This widget could not be displayed.