Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Network upgrade question...

Can a Catalyst 3750 switch replace a HP procurve switch without much configuration?

other than configuring the ports, there just needs to be a route on the 3750 pointing all traffic to the gateway correct?

2 ACCEPTED SOLUTIONS

Accepted Solutions
Silver

Re: Network upgrade question...

then all you will need is a IP address and default gateway for management access to the switch.

Conf t - interface vlan X

ip address x.x.x.x x.x.x.x

no shut

ip default gateway x.x.x.x

Silver

Re: Network upgrade question...

does the remote switch connect to a router?

or is it just a fiber run to another building?

Not sure I understand what the topology is.

If you are connecting to the remote site via WAN router then the vlan number doesnt matter. You are routing subnets not vlans. The default route for client will be that of the remote router

at its simplest form, you should put all ports into the vlan and manage through the vlan interface.

if you are extending the vlan from your office across layer two, then just add users ports to the vlan, and create another ip address for the switch

10 REPLIES
Purple

Re: Network upgrade question...

It depends on how its being used . Is being used as strictly a layer 2 switch or are you routing with the switch and using dynamic routing protocols or static routes ?

New Member

Re: Network upgrade question...

i think i am just going to leave it as strictly a layer 2 switch..

static routes will be kept on the router not switch at this location...

Silver

Re: Network upgrade question...

then all you will need is a IP address and default gateway for management access to the switch.

Conf t - interface vlan X

ip address x.x.x.x x.x.x.x

no shut

ip default gateway x.x.x.x

New Member

Re: Network upgrade question...

ok i did exactly what you suggested on this new switch..

I did a show interfaces status... and this is what i got...

Fa3/0/1 notconnect 1 auto auto 10/100BaseTX

Fa3/0/2 notconnect 1 auto auto 10/100BaseTX

Fa3/0/3 notconnect 1 auto auto 10/100BaseTX

Fa3/0/4 notconnect 1 auto auto 10/100BaseTX

Fa3/0/5 notconnect 1 auto auto 10/100BaseTX

Fa3/0/6 notconnect 1 auto auto 10/100BaseTX

Fa3/0/7 notconnect 1 auto auto 10/100BaseTX

Fa3/0/8 notconnect 1 auto auto 10/100BaseTX

i changed the mangement VLAN to 21, but is it okay to leave these at Vlan1 ? and it should work like the dummy HP Procurve?

ofcourse i only shown the first 8...i didnt want to make it redundant :)

Purple

Re: Network upgrade question...

You won't be able to have the management vlan in 21 and the ports in one unless you plan on trunking to the layer 3 device doing the routing. If the management vlan 21 is the same as the user vlan then set all the ports into vlan 21.

New Member

Re: Network upgrade question...

well...since its a remote location, should it be on the same VLAN as it is in my building or can it be on 21?

all my workstations in my building are on VLAN 16... ofcourse everything in my building is going to the default gateway...and everything in the remote location is being point to my router in my building which is going to the default gateway..

Any thoughts?

Silver

Re: Network upgrade question...

does the remote switch connect to a router?

or is it just a fiber run to another building?

Not sure I understand what the topology is.

If you are connecting to the remote site via WAN router then the vlan number doesnt matter. You are routing subnets not vlans. The default route for client will be that of the remote router

at its simplest form, you should put all ports into the vlan and manage through the vlan interface.

if you are extending the vlan from your office across layer two, then just add users ports to the vlan, and create another ip address for the switch

New Member

Re: Network upgrade question...

it connects to a Cisco 2800 router which connects to our metro to our building..

basically what i just did was...

#1 gave the switch an ip address

#2 set the default gateway of the inside interface of the metro router which connects back to us

#3 and set the VLAN management to 21 (since cisco recommends not to leave it at 1)

so all my ports on this should have..

switchport access VLAN 21 .... correct?

Then i should be good to go! right?

New Member

Re: Network upgrade question...

Great that will work fine

DAK

New Member

Re: Network upgrade question...

i think i am just going to leave it as strictly a layer 2 switch..

static routes will be on this one..

128
Views
0
Helpful
10
Replies
CreatePlease to create content