Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Nexus 5548 - ipv6 interface

Is it possible at nexus 5548 with daughter card to assign ipv6 address to interface?

I have gone thru lot's od docs cisco says on tech doc:

• IPv6 Routing Protocols: Static, Open Shortest Path First Version 3 (OPFv3), Border Gateway Protocol (BGPv6), Enhanced Interior Gateway Routing Protocol (EIGRPv6)

• IPv6 VRF Lite

So I am assuming is supporting IPv6 routing.

command line:

NEXUS-1(config-if)# ipv6 add?

                         ^

% Invalid command at '^' marker.

?

                         ^

% Invalid command at '^' marker.

NEXUS-1(config-if)# ipv6 ?

  port  Port policy

I was looking for feature to turn on but doesn't looks there is one.

Doesn't seem that I can turn it on by ipv6 unicast-routing.


Everyone's tags (4)
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Nexus 5548 - ipv6 interface

Marcin,

Nope ipv6 is not supported on 5.1(3)N2(1) i.

Were as it is supported on 5.2 release.

Feature History for IPv6

Table 3-5 lists the release history for this feature.

Table 3-5     Feature History for IPv6

Feature Name

Releases

Feature Information

IPv6

5.2(1)

This feature was introduced.

http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/unicast/521_N11/l3_ipv6.html#wp1200855

HTH

Regards

Inayath

'***********

Please rate and mark the post as answered so others can benefit from it.


5 REPLIES

Re: Nexus 5548 - ipv6 interface

It might be something to do with your version of NX-OS.

Don't forget to rate all helpful posts.

https://supportforums.cisco.com/thread/2077565

New Member

Re: Nexus 5548 - ipv6 interface

My NX-OS is 5.1(3)N2(1) is that one supporting ipv6?

Is quite weird that nexus doesn’t support ipv6 where there is no many ipv4 left.

CISCO should really sort that out, we have spent over £50k for switches and we are not able to do dual stack ;(

Cisco Employee

Nexus 5548 - ipv6 interface

Marcin,

Nope ipv6 is not supported on 5.1(3)N2(1) i.

Were as it is supported on 5.2 release.

Feature History for IPv6

Table 3-5 lists the release history for this feature.

Table 3-5     Feature History for IPv6

Feature Name

Releases

Feature Information

IPv6

5.2(1)

This feature was introduced.

http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/unicast/521_N11/l3_ipv6.html#wp1200855

HTH

Regards

Inayath

'***********

Please rate and mark the post as answered so others can benefit from it.


New Member

Nexus 5548 - ipv6 interface

Does it mean that we have to buy new NX OS update for brand new switches?

We have received those switches with this software yesterday.

Or do I need to buy ASR to do IPv6 routing?

thanks

Cisco Employee

Nexus 5548 - ipv6 interface

Marcin,

Just go ahed and upgrade the firmware.

Regards

Inayath

771
Views
5
Helpful
5
Replies
CreatePlease login to create content