Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

Silver

Nexus 7K 6.1 code and F2 series module how to enable priority queue for IPT

Hi,

I have a 7K running 6.1 code, on F series line cards. I  need to set it to prioritise DSCP EF marked traffic, that's all at this stage, but am  unclear on the configuration steps required. The packets will already be  marked, I just need to ensure they end up in a priority queue.

Anyone done this who can point me at an example configuration, I need a starting point.

2 REPLIES
Bronze

Re: Nexus 7K 6.1 code and F2 series module how to enable priorit

Here is cofiguration guide for qos

http://www.cisco.com/en/US/docs/switches/datacenter/sw/6_x/nx-os/qos/configuration/guide/queuing.html#wp1101680

Sent from Cisco Technical Support iPhone App

Silver

Re: Nexus 7K 6.1 code and F2 series module how to enable priorit

Thanks for the reply, I had already had a look through that manual, and made a start, but it didnt work. Now back at site, taken another look at this and come up with the following:

qos copy policy type queuing default-4q-8e-out-policy prefix 20G-EGRESS-


sh policy-map type queuing 20G-EGRESS-4q-8e-out

! Enter policy config mode:
policy-map type queuing 20G-EGRESS-4q-8e-out

! show the default queuing policy map created:

sh policy-map type queuing 20G-EGRESS-4q-8e-out


  Type queuing policy-maps
  ========================

  policy-map type queuing 20G-EGRESS-4q-8e-out
    class type queuing 1p3q1t-8e-out-pq1
      priority level 1
    class type queuing 1p3q1t-8e-out-q2
      bandwidth remaining percent 33
    class type queuing 1p3q1t-8e-out-q3
      bandwidth remaining percent 33
    class type queuing 1p3q1t-8e-out-q-default
      bandwidth remaining percent 33

! Apply to an interface:

int po3
service-policy type queuing output 20G-EGRESS-4q-8e-out

sh run int po3

!Command: show running-config interface port-channel3
!Time: Tue Jul 10 16:07:55 2012

version 6.0(3)

interface port-channel3
  description *** VPC Uplink to SeminarA ***
  switchport
  switchport mode trunk
  switchport trunk native vlan 499
  switchport trunk allowed vlan 300-302,310-314,320-323,350,353
  switchport trunk allowed vlan add 400,499,999
  service-policy type queuing output 20G-EGRESS-4q-8e-out
  vpc 3


! To show the cos to queue mapppings, check one of the port channel physical

members:

sh queuing interface e3/3

Egress Queuing for Ethernet3/3 [Interface]
-------------------------------------------
Template: 4Q8E
-------------------------------------------------
Que# Group Bandwidth% PrioLevel Shape%     CoSMap
-------------------------------------------------
   0     0          -      High      -        5-7
   1     1         33         -      -        3-4
   2     2         33         -      -        1-2
   3     3         33         -      -          0


Ingress Queuing for Ethernet3/3 [System]
-------------------------------------------
Trust: Trusted
-----------------------------------
Que# Group Qlimit% IVL      CoSMap
-----------------------------------
   0     1      90   0         0-4
   1     0      10   5         5-7

Yet to test fully, but I think this will do the job. Only issue is that I have to use CoS as opposed to DSCP for the queues, but the IPT traffic should already have the correct CoS value set in the inbound traffic.

Final config:

qos copy policy type queuing default-4q-8e-out-policy prefix 20G-EGRESS-

policy-map type queuing 20G-EGRESS-4q-8e-out

int po3

service-policy type queuing output 20G-EGRESS-4q-8e-out

1737
Views
5
Helpful
2
Replies