Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

NM-1FE-TX does not work with 2691 Router

*** Address Parity Error ***
PC = 0xbfc00d20, Cause = 0xd4000, Status Reg = 0x3041e803
Failure detected during ROMMON start-up tests. Restart ROMMON.

System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.

Can somebody please tell me why this error came?

only thing i did was insert external CF  card on router.

That card is blank it has no IOS on it.

I did power cycle the router it is stuck at

System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.

System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
c2691 processor with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with parity disabled


Readonly ROMMON initialized
program load complete, entry point: 0x80008000, size: 0xcd60
program load complete, entry point: 0x80008000, size: 0xcd60

program load complete, entry point: 0x80008000, size: 0x245ac68
Self decompressing the image : #################################################
################################################################################
######################################################################## [OK]

should i again  reboott the router?

thanks

2 REPLIES
New Member

2691 router unable to access by console

Hi,

More info on issue---

i inserted this FE  card on router

NAME: "Unknown", DESCR: "Unknown"

PID: NM-1FE-TX=        , VID: 1.0, SN: 12949267

nt detected on slot 1

OIR not supported on this platform

Inserting or removing modules while powered on may cause router to crash!

again i rebooted the card.

NAME: "Unknown", DESCR: "Unknown"
PID: NM-1FE-TX=        , VID: 1.0, SN: 12949267

when i inserted it router console says

i reloaded the router but it do not see new FE  port

Slot 1:

        Unknown (type 68) Port adapter

        Port adapter is disabled

        Port adapter insertion time unknown

        EEPROM contents at hardware discovery:

        Hardware revision 1.0           Board revision D0

        Serial number     12949267      Part number    800-03490-02

        FRU Part Number     NM-1FE-TX=

        Test history      0x0           RMA number     00-00-00

        EEPROM format version 1

        EEPROM contents (hex):

          0x00: 01 44 01 00 00 C5 97 13 50 0D A2 02 00 00 00 00

          0x10: 68 0A 21 00 99 04 12 00 FF FF FF FF FF FF FF FF

          0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

          0x30: FF FF FF FF FF FF FF FF FF FF FF FF

is this card FE  not compatible with router ?

card has green lights on link and 100mbps.

thanks

mahesh

New Member

2691 router unable to access by console

More info

Router has latest IOS

Router# sh ver
Cisco IOS Software, 2600 Software (C2691-ADVENTERPRISEK9-M), Version 12.4(25d),
RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 18-Aug-10 05:35 by prod_rel_team

ROM: System Bootstrap, Version 12.2(8r)T2, RELEASE SOFTWARE (fc1)

Router uptime is 34 minutes
System returned to ROM by reload
System image file is "flash:c2691-adventerprisek9-mz.124-25d.bin"

330
Views
0
Helpful
2
Replies