06-20-2012 05:36 AM - edited 03-07-2019 07:21 AM
Hi all,
I got a CAT4506-E with the following setup:
test#sh module
Chassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 6 Sup 6L-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6L-E JAE161900EK
2 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE160500V7
3 48 10/100/1000BaseT (RJ45)V, Cisco/IEEE WS-X4548-GB-RJ45V JAE161201Y5
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 5057.a89f.6f00 to 5057.a89f.6f05 3.0 12.2(44r)SG1 15.0(2)SG4 Ok
2 c464.138b.2d10 to c464.138b.2d3f 2.6 Ok
3 f0f7.555a.4f80 to f0f7.555a.4faf 5.1 Ok
On module 3, there is no PoE available.
test#show power inline module 3
Available:0(w) Used:0(w) Remaining:0(w)
Interface Admin Oper Power(Watts) Device Class
From PS To Device
--------- ------ ---------- ---------- ---------- ------------------- -----
Gi3/1 auto off 0.0 0.0 n/a n/a
Gi3/2 auto off 0.0 0.0 n/a n/a
Gi3/3 auto off 0.0 0.0 n/a n/a
Tried another Slot, another supervisorcard -> the same issue.
Here the power details:
test#show power detail
Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C45-1400AC AC 1400W good good n.a.
PS2 PWR-C45-1400AC AC 1400W good good n.a.
Power supplies needed by system : 1
Power supplies currently available : 2
Power Summary Maximum
(in Watts) Used Available
---------------------- ---- ---------
System Power (12V) 440 1360
Inline Power (-50V) 0 0
Backplane Power (3.3V) 0 40
---------------------- ---- ---------
Total 440 1400
Watts Used of System Power(12V)
Mod Model budgeted instantaneous peak out of reset in reset
---- ------------------- -------- ------------- ------ ------------ --------
1 WS-X45-SUP6L-E 200 -- -- 200 200
2 WS-X4548-GB-RJ45 60 -- -- 60 25
3 WS-X4548-GB-RJ45V 60 -- -- 60 25
-- Fan Tray 120 -- -- -- --
------------------------- -------- ------------- ------ ------------ --------
Total 440 -- -- 320 250
Watts used of Chassis Inline Power (-50V)
Inline Power Admin Inline Power Oper
Mod Model PS Device PS Device Efficiency
---- ------------------- ---------------- ---------------- ----------
1 WS-X45-SUP6L-E - - - - -
2 WS-X4548-GB-RJ45 - - - - -
3 WS-X4548-GB-RJ45V 0 0 0 0 89
------------------------- ---------------- ---------------- ----------
Total 0 0 0 0
Who has any idea?
Thanks,
Norbert
Solved! Go to Solution.
06-20-2012 06:24 AM
Your power supplies do not support PoE. Check it out here:
and just find your power supply model number.
Ordering Information
To place an order, visit the Cisco Ordering homepage or refer to Tables 12 through 14.
Table 12. Cisco Catalyst 4500 Power-Supply Ordering Information
Part Number | Product Name |
PWR-C45-1000AC | Cisco Catalyst 4500 1000 WAC Power Supply (Data Only) |
PWR-C45-1400AC | Cisco Catalyst 4500 1400 WAC Power Supply (Data Only) |
06-20-2012 06:24 AM
Your power supplies do not support PoE. Check it out here:
and just find your power supply model number.
Ordering Information
To place an order, visit the Cisco Ordering homepage or refer to Tables 12 through 14.
Table 12. Cisco Catalyst 4500 Power-Supply Ordering Information
Part Number | Product Name |
PWR-C45-1000AC | Cisco Catalyst 4500 1000 WAC Power Supply (Data Only) |
PWR-C45-1400AC | Cisco Catalyst 4500 1400 WAC Power Supply (Data Only) |
02-15-2018 01:40 AM
Cisco-4500#sho env
no temperature alarms
Module Sensor Temperature Status
------+--------------------------+--------------------+------------
3 air inlet 21C (51C,65C,68C) ok
3 air outlet 31C (69C,83C,86C) ok
4 air inlet 20C (51C,65C,68C) ok
4 air outlet 29C (69C,83C,86C) ok
Power Fan Inline
Supply Model No Type Status Sensor Status
------ ---------------- --------- ----------- ------- -------
PS1 PWR-C45-2800AC AC 2800W good good good
PS2 PWR-C45-2800AC AC 2800W good good good
Power supplies needed by system : 1
Power supplies currently available : 2
Chassis Type : WS-C4507R-E
Power consumed by backplane : 40 Watts
Switch Bandwidth Utilization : 0%
Supervisor Led Color : Green
Module 1 Status Led Color : Green
Module 2 Status Led Color : Green
Module 3 Status Led Color : Green
Module 4 Status Led Color : Green
Module 5 Status Led Color : Green
Fantray : Good
Fantray removal timeout : 30
Power consumed by Fantray : 135 Watts
(Still no power,)
Help
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: