Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

not able to enable multicast on cisco 3560 swtich

hi,

I want to enable multicast  sparse mode  on cisco 3560 switch.I need to enabled it on L3 svi but when i go the interface mode i cant see the commands

any body can advise

is this license issue

EC-38th-IPTV-SW#sh version

Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 15.0(1)SE2, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2011 by Cisco Systems, Inc.

Compiled Thu 22-Dec-11 00:16 by prod_rel_team

ROM: Bootstrap program is C3560E boot loader

BOOTLDR: C3560E Boot Loader (C3560E-HBOOT-M) Version 12.2(44r)SE5, RELEASE SOFTWARE (fc3)

TEC-38th-IPTV-SW uptime is 12 weeks, 4 days, 18 hours, 18 minutes

System returned to ROM by power-on

System image file is "flash:/c3560e-universalk9-mz.150-1.SE2.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

License Level: ipbase

License Type: Permanent

Next reload license Level: ipbase

cisco WS-C3560E-48PD (PowerPC405) processor (revision D0) with 131072K bytes of memory.

Processor board ID FDO1212V0FC

Last reset from power-on

3 Virtual Ethernet interfaces

1 FastEthernet interface

52 Gigabit Ethernet interfaces

2 Ten Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address       : 00:1F:CA:98:94:80

Motherboard assembly number     : 73-10320-12

Motherboard serial number       : FDO12110TGG

Model revision number           : D0

Motherboard revision number     : B0

Model number                    : WS-C3560E-48PD-SF

Daughterboard assembly number   : 800-28590-01

Daughterboard serial number     : FDO12110NZK

System serial number            : FDO1212V0FC

Top Assembly Part Number        : 800-28447-02

Top Assembly Revision Number    : C0

Version ID                      : V01

CLEI Code Number                : COM7900ARA

Hardware Board Revision Number  : 0x01

Switch Ports Model              SW Version            SW Image                

------ ----- -----              ----------            ----------              

*    1 54    WS-C3560E-48PD     15.0(1)SE2            C3560E-UNIVERSALK9-M    

  • LAN Switching and Routing
2 REPLIES
Hall of Fame Super Silver

not able to enable multicast on cisco 3560 swtich

I have checked the Cisco Feature Navigator for this release and it says that this software with the IP Base license should support PIM Multicast routing. So it looks like it is not a licensing issue.

Have you enabled ip multicast routing?

HTH

Rick

VIP Purple

not able to enable multicast on cisco 3560 swtich

These sort of switch model before you configure PIM under interfaces you have to enable multicast globally using below command. Pls check whether you have configured it

"ip multicast-routing distributed"

HTH

Rasika

**** Pls rate all useful responses****

267
Views
0
Helpful
2
Replies