03-04-2009 03:51 PM - edited 03-06-2019 04:23 AM
I cannot get the PA-MC-8T1 to work on our 6509-NEB. See the flexwan module ok but not the PA, IOS is 12.1(27b) so I am ok there. I am wondering if it is an issue with not being supported by the SUP1A-2GE. Any help would be appreciated.
Solved! Go to Solution.
03-05-2009 09:25 AM
Yes, correct, flexwan is hot swappable, PA might be not. Most time, I just suggest customer to pull out flexwan when replacing PA.
03-04-2009 09:10 PM
In "show diag", did you see PA-MC-8T1?
03-05-2009 08:18 AM
Show diag below, flexwan is in slot 7, looks like it does see it in Bay 0???
Thanks
C6509#show diag
Slot 7: Logical_index 14
FlexWan controller
Board is analyzed ipc ready
HW rev 1.3, board revision B0
Serial Number: SAD04320GD6 Part number: 73-3869-07
Slot database information:
Flags: 0x2004 Insertion time: 0x240BAD44C (16:46:01 ago)
Controller Memory Size:
56 MBytes CPU Memory
8 MBytes Packet Memory
64 MBytes Total on Board SDRAM
IOS (tm) cwlc Software (cwpa-DW-M), Version 12.1(27b)E, RELEASE SOFTWARE
(fc2)
PA Bay 0 Information:
Multi-channel (T1) PA, 8 ports
EEPROM format version 1
HW rev 1.00, Board revision A0
Serial number: 23119576 Part number: 73-2488-07
Slot 7: Logical_index 15
FlexWan controller
Board is analyzed ipc ready
HW rev 1.3, board revision B0
Serial Number: SAD04320GD6 Part number: 73-3869-07
Slot database information:
Flags: 0x2004 Insertion time: 0x240BAC474 (16:46:08 ago)
CWAN Controller Memory Size: Unknown
03-05-2009 08:33 AM
But "CWAN Controller Memory Size: Unknown" does not sound right. Can you try to reseat both PA and flexwan? You can try Bay 1 as well.
03-05-2009 09:19 AM
I reset both of them just a day or so ago. Bay 1 has a supervisor module. I have bays 3 - 6 available, does it matter which bay?
03-05-2009 09:22 AM
flexwan has two slots, we call it bay 0 and bay 1. You can put PA in another slot of flexwan if possible.
03-05-2009 09:23 AM
OK, I got you. I understand the PA is not hot swap so I need to pull the whole flexwan, correct?
03-05-2009 09:25 AM
Yes, correct, flexwan is hot swappable, PA might be not. Most time, I just suggest customer to pull out flexwan when replacing PA.
03-05-2009 10:05 AM
That looks like it did it! So just a bad bay perhaps?
03-05-2009 10:14 AM
Could be.
If you don't mind, you can try to put it back to bay 0 again. If it still has issue, you need to replace flexwan.
03-05-2009 10:42 AM
Looks like it is still good moved back to bay 0????
C6509#show diag
Slot 7: Logical_index 14
FlexWan controller
Board is analyzed ipc ready
HW rev 1.3, board revision B0
Serial Number: SAD04320GD6 Part number: 73-3869-07
Slot database information:
Flags: 0x2004 Insertion time: 0x244CC31B4 (00:13:20 ago)
Controller Memory Size:
56 MBytes CPU Memory
8 MBytes Packet Memory
64 MBytes Total on Board SDRAM
IOS (tm) cwlc Software (cwpa-DW-M), Version 12.1(27b)E, RELEASE SOFTWARE
(fc2)
PA Bay 0 Information:
Multi-channel (T1) PA, 8 ports
EEPROM format version 1
HW rev 1.00, Board revision A0
Serial number: 23119576 Part number: 73-2488-07
Slot 7: Logical_index 15
FlexWan controller
Board is analyzed ipc ready
HW rev 1.3, board revision B0
Serial Number: SAD04320GD6 Part number: 73-3869-07
Slot database information:
Flags: 0x2004 Insertion time: 0x244CC23C0 (00:13:31 ago)
Controller Memory Size:
56 MBytes CPU Memory
8 MBytes Packet Memory
64 MBytes Total on Board SDRAM
IOS (tm) cwlc Software (cwpa-DW-M), Version 12.1(27b)E, RELEASE SOFTWARE
(fc2)
03-05-2009 10:46 AM
That's why I asked you to try it again in bay 0. :)
I guess that it might not be seated well.
03-05-2009 10:51 AM
hmmm. OK well thanks for the help!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: