Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

PBR feature not working on Nexus 5K

All

 

i am trying to enable policy based routing feature on Nexus switch, but i am getting error, command not available.

 show version
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_series_home.html
Copyright (c) 2002-2013, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software are covered under the GNU Public
License. A copy of the license is available at
http://www.gnu.org/licenses/gpl.html.

Software
  BIOS:      version 3.6.0
  loader:    version N/A
  kickstart: version 6.0(2)N1(2a)
  system:    version 6.0(2)N1(2a)
  Power Sequencer Firmware:
             Module 1: version v1.0
             Module 3: version v5.0
  Microcontroller Firmware:        version v1.2.0.1
  SFP uC:    Module 1: v1.0.0.0
  QSFP uC:   Module not detected
  BIOS compile time:       05/09/2012
  kickstart image file is: bootflash:///n5000-uk9-kickstart.6.0.2.N1.2a.bin
  kickstart compile time:  5/20/2013 9:00:00 [05/20/2013 17:43:34]
  system image file is:    bootflash:///n5000-uk9.6.0.2.N1.2a.bin
  system compile time:     5/20/2013 9:00:00 [05/20/2013 20:18:17]


Hardware
  cisco Nexus5548 Chassis ("O2 32X10GE/Modular Universal Platform Supervisor")
  Intel(R) Xeon(R) CPU         with 8262944 kB of memory.
  Processor Board ID FOC17165AVX

  Device name: NFRA1L3CORE1
  bootflash:    2007040 kB

Kernel uptime is 468 day(s), 3 hour(s), 45 minute(s), 44 second(s)

Last reset
  Reason: Unknown
  System version: 6.0(2)N1(2a)
  Service:

plugin
  Core Plugin, Ethernet Plugin

 

 show feature
Feature Name          Instance  State
--------------------  --------  --------
Flexlink              1         disabled
amt                   1         disabled
bgp                   1         enabled
cts                   1         disabled
dhcp                  1         enabled
dot1x                 1         disabled
eigrp                 1         disabled
eigrp                 2         disabled
eigrp                 3         disabled
eigrp                 4         disabled
eth_port_sec          1         disabled
fcoe                  1         disabled
fcoe-npv              1         disabled
fex                   1         enabled
glbp                  1         disabled
hsrp_engine           1         enabled
interface-vlan        1         enabled
isis                  1         disabled
isis                  2         disabled
isis                  3         disabled
isis                  4         disabled
lacp                  1         enabled
ldap                  1         disabled
lldp                  1         enabled
msdp                  1         disabled
oim                   1         disabled
ospf                  1         enabled
ospf                  2         enabled (not-running)
ospf                  3         enabled (not-running)
ospf                  4         enabled (not-running)
ospfv3                1         disabled
ospfv3                2         disabled
ospfv3                3         disabled
ospfv3                4         disabled
pbr                   1         disabled
pim                   1         disabled
poe                   1         disabled
private-vlan          1         disabled
privilege             1         disabled

NFRA1L3CORE1# configure terminal

Enter configuration commands, one per line.  End with CNTL/Z.

NFRA1L3CORE1(config)# feature ?

  bgp             Enable/Disable Border Gateway Protocol (BGP)

  cts             Enable/Disable CTS

  dhcp            Enable/Disable DHCP Snooping

  dot1x           Enable/Disable dot1x

  eigrp           Enable/Disable Enhanced Interior Gateway Routing Protocol (EIGRP)

  fcoe            Enable/Disable FCoE/FC feature

  fcoe-npv        Enable/Disable FCoE NPV feature

  fex             Enable/Disable FEX

  flexlink        Enable/Disable Flexlink

  hsrp            Enable/Disable Hot Standby Router Protocol (HSRP)

  http-server     Enable/Disable http-server

  interface-vlan  Enable/Disable interface vlan

  lacp            Enable/Disable LACP

  msdp            Enable/Disable Multicast Source Discovery Protocol (MSDP)

  ntp             Enable/Disable NTP

  ospf            Enable/Disable Open Shortest Path First Protocol (OSPF)

  ospfv3          Enable/Disable Open Shortest Path First Version 3 Protocol (OSPFv3)

  pim             Enable/Disable Protocol Independent Multicast (PIM)

  port-security   Enable/Disable port-security

  private-vlan    Enable/Disable private-vlan

  privilege       Enable/Disable IOS type privilege level support

  ptp             Enable/Disable PTP

  rip             Enable/Disable Routing Information Protocol (RIP)

  scp-server      Enable/Disable SCP server

  sftp-server     Enable/Disable SFTP server

  ssh             Enable/Disable ssh

  tacacs+         Enable/Disable tacacs+

  telnet          Enable/Disable telnet

  udld            Enable/Disable UDLD

  vpc             Enable/Disable VPC (Virtual Port Channel)

  vrrp            Enable/Disable Virtual Router Redundancy Protocol (VRRP)

  vtp             Enable/Disable Vlan Trunking Protocol (VTP)

 

 

NFRA1L3CORE1(config)# fea

feature       feature-set

NFRA1L3CORE1(config)# feature pbr

                               ^

Can someone suggest me what can be the issue? Switch have LAN_ENTERPRISE_SERVICES_PKG license.

 

Regards

Rashpal Singh

2 REPLIES
VIP Super Bronze

See table-5 in this link:http

See table-5 in this link:

http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/licensing/guide/b_Cisco_NX-OS_Licensing_Guide/b_Cisco_NX-OS_Licensing_Guide_chapter_01.html#fntarg_13

Note 19:

The LAN_BASE_SERVICES_PKG license needs to be installed in order to use the LAN_ENTERPRISE_SERVICES_PKG license.

HTH

New Member

Thanks RezaSwitch have both

Thanks Reza

Switch have both the LAN_BASE_SERVICES_PKG and LAN_ENTERPRISE_SERVICES_PKG license installed.

 

Regards

Rashpal Singh

263
Views
0
Helpful
2
Replies
CreatePlease to create content