pleas frind i need help in switch 2900XL

[Tareq Emad Al Asfoor]

hi frind

I need help . i have cisco switch 2900 XL , I install new image , but when it reload , this appear for me

flashfs[1]: Initialization complete.
...done Initializing C2900XL flash.
C2900XL POST: System Board Test: Passed
C2900XL POST: Daughter Card Test: Passed
C2900XL POST: CPU Buffer Test: Passed
C2900XL POST: CPU Notify RAM Test: Passed
C2900XL POST: CPU Interface Test: Passed
C2900XL POST: Testing Switch Core: Passed
C2900XL POST: Testing Buffer Table: Passed
C2900XL POST: Data Buffer Test: Passed
C2900XL POST: Configuring Switch Parameters: Passed
C2900XL POST: Ethernet Controller Test: Passed
C2900XL POST: MII Test: Passed
cisco WS-C2924-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K byte
s of memory.

Cisco Internetwork Operating System Software
IOS (tm) C2900XL Software (C2900XL-C3H2L9S-M), Version 12.0(5)WC17, RELEASE SOFT
WARE (fc1)
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Tue 13-Feb-07 15:28 by antonino
00:00:31: %IMAGE_MISMATCH-3-MALIBU_IMAGE_MISMATCH:
LRE firmware not supported by switch hardware.
Please download a non-LRE image.

what is that , and what is the correct imag (.bin) to install in it

regards ...

[Tareq Emad Al Asfoor]

dear glen

i do that , and make boot from it but when i reload it during the reload the image , the error appear for me

this error for the controlar

% Invalid input detected at '^' marker

% Invalid input detected at '^' marker

% Invalid input detected at '^' marker

% Invalid input detected at '^' marker

                .

                .

                .

and  when i [use this image ( c2900xl-c3h2l9s-mz.120-5.WC17.bin) this error not appear , but this appear

Please download a non-LRE image

and also canot add any VLAN

so where the problem , i hop to help me

[Nagaraja Thanthry]

Hello,

Can you please post the output of "show flash:" and "show run | I boot"

commands here?

Regards,

NT

[Tareq Emad Al Asfoor]

Switch>sh version

Cisco Internetwork Operating System Software

IOS (tm) C2900XL Software (C2900XL-C3H2L9S-M), Version 12.0(5)WC17, RELEASE SOFT

WARE (fc1)

Copyright (c) 1986-2007 by cisco Systems, Inc.

Compiled Tue 13-Feb-07 15:28 by antonino

Image text-base: 0x00003000, data-base: 0x0038A0D8

ROM: Bootstrap program is C2900XL boot loader

Switch uptime is 1 hour, 19 minutes

System returned to ROM by power-on

System image file is "flash:c2900xl-c3h2l9s-mz.120-5.WC17.bin"

cisco WS-C2924-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K byte

s of memory.

Processor board ID FAB0345Y0N9, with hardware revision 0x01

Last reset from power-on

Processor is running Enterprise Edition Software

Cluster command switch capable

Cluster member switch capable

24 FastEthernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:30:94:63:0B:C0
Motherboard assembly number: 73-3382-07
Power supply part number: 34-0834-01
Motherboard serial number: FAB034466K0
Power supply serial number: DAB03352M83
Model revision number: A0
Model number: WS-C2924-XL-A
System serial number: FAB0345Y0N9
Configuration register is 0xF

Switch#dir flash:
Directory of flash:/

  2  -rwx     1929856   Mar 01 1993 00:50:55  c2900xl-c3h2l9s-mz.120-5.WC17.bin
  3  -rwx          45   Mar 01 1993 00:52:13  env_vars
  4  -rwx        1021   Mar 01 1993 00:53:05  config.text

3612672 bytes total (1679872 bytes free)

Switch#show boot
BOOT path-list:      flash:c2900xl-c3h2l9s-mz.120-5.WC17.bin
Config file:         flash:config.text
Enable Break:        no
Manual Boot:         no
HELPER path-list:
NVRAM/Config file
      buffer size:   32768

[Tareq Emad Al Asfoor]

any body found the problem ??????????????

[Nagaraja Thanthry]

Hello,

You still have incorrect image in the switch flash. Please do the following:

-- Login into Cisco.com and download c2900xl-c3h2s-mz.120-5.WC17.bin image

-- On Google, search for TFTPd32 and download it onto your PC

-- Install TFTPd32 on your PC

-- Ping the 2900XL switch from your PC. Make sure that the PING is

successful

-- Ping your PC from 2900XL and make sure that it is successful as well. If

the PING is not successful, check your PC and turn off any firewall

(Windows/Antivirus Software/VPN) and try again. Now start the TFTPd32

program (double click on the shortcut on your desktop)

-- Move the image you had downloaded earlier to C:/Program Files/tftpd32

folder on your PC

-- Now, delete the old image from the 2900XL

switch#delete flash:/c2900xl-c3h2l9s-mz.120-5.WC17.bin

-- Now copy the new image to the switch:

switch#copy tftp: flash:

Address or name of remote host []?

Source filename []? c2900xl-c3h2s-mz.120-5.WC17.bin

Destination filename ?

Now reboot the switch. You should be able to reboot with the new image.

Hope this helps.

Regards,

NT

[Tareq Emad Al Asfoor]

dear ..

i install this image c2900xl-c3h2s-mz.120-5.WC17.bin through Xmodem , after the install finsh and reload it , the error appear for me

% Invalid input detected at '^' marker.

% Invalid input detected at '^' marker.

% Invalid input detected at '^' marker.

% Invalid input detected at '^' marker.

so  now whta u say me to do

[Nagaraja Thanthry]

Hello,

You are getting those because some configuration line that were entered by

the earlier software version are not compatible with the new image. This

happens when you boot up the switch first time with the new image. If you

issue a "write mem" command and reload, you should not see that error

message again.

Hope this helps.

Regards,

NT

[Tareq Emad Al Asfoor]

dear Naqaraja..

i install the image (c2900xl-c3h2s-mz.120-5.WC17.bin) and write memory then reload it

this appear for me after reload

Model number: WS-C2924-XL-A
System serial number: FAB0345Y0N9
controller LongReachEthernet 0
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 1
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 2
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 3
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 5
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 6
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 7
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 8
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 9
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 10
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 11
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 12
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 13
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 14
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 15
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 16
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 17
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 18
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 19
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 20
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 21
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 22
^
% Invalid input detected at '^' marker.

controller LongReachEthernet 23
^
% Invalid input detected at '^' marker.

Press RETURN to get started!

Switch#show boot
BOOT path-list:      flash:c2900xl-c3h2s-mz.120-5.WC17.bin
Config file:         flash:config.text
Enable Break:        no
Manual Boot:         no
HELPER path-list:
NVRAM/Config file
      buffer size:   32768

Switch#dir flash:
Directory of flash:/

  2  -rwx     1811968   Mar 01 1993 00:50:37  c2900xl-c3h2s-mz.120-5.WC17.bin
  4  -rwx          43   Mar 01 1993 00:55:05  env_vars
  5  -rwx        1827   Mar 01 1993 00:55:59  config.text

3612672 bytes total (1797120 bytes free)

So Now where the problem ???????

[Tareq Emad Al Asfoor]

what happend ,no body can reslove mr trouble ???????????

[glen.grant]

  You might try deleting the "config.txt"  file in flash and then reload the switch and see what happens .  

[Tareq Emad Al Asfoor]

Dear Naqaraja , glen

and all my friend that response with my problem

I think my problem is resolve i now check it , iam very gratefull for all

regards ...