Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Plz Help

Hello

Have a look to the Attachment...

Kindly;Can any one explain to me what this mean:i disable all ipv6 on vlan 198 and 199 but the Problems Still EXIST.

PLZ HELP ME TO FIX THIS PROBLEM

10XS

6 REPLIES
Hall of Fame Super Blue

Re: Plz Help

Ali

As others have suggested, you need to track down the mac-address. So in your wireshark capture select one of the entries and

1) In the wireshark Gui go to the middle window and click on the + next to "Ethernet II, ...

2) Record the full mac-address. Note the mac-address not the IP address. As an example lets say the mac-address is

0008.02e1.832a

Note it may also be written as such

00-08-02-e1-83-2a

3) Log onto one of your 6500 switches and enter the following command

"sh mac-address-table address 0008.02e1.832a"

The output will tell you what port it is on.

4) If the port is an access port on the 6500 then you just need to find out what is attached to that port. if the port is a trunk port to another switch then you need to

5) telnet to that next switch and repeat the process ie. enter

"sh mac-address-table address 0008.02e1.832a"

Depending on your switch topology you may need to do this a few times until you find the correct switch. You are looking for a port configured as an access port.

As long as you have disabled ipv6 on all your network kit, assuming you don't need it, then it will very probably be a host PC. Follow the above to track it down.

Jon

New Member

Re: Plz Help

hello Jon!

10xs for reply.but look command didn't works:

6509#sh mac-address-table dynamic fe80::9d58:ecda:bc:4dfd

^

% Invalid input detected at '^' marker.

6509#sh mac-address-table dynamic fe:80:9d:58:ec:da:bc:4d:fd

^

% Invalid input detected at '^' marker.

6509#sh mac-address-table add

6509#sh mac-address-table address 0218:411d:b301

^

% Invalid input detected at '^' marker.

6509#sh mac-address-table address fe:80:9d:58:ec:da:bc:4d:fd

^

% Invalid input detected at '^' marker.

New Member

Re: Plz Help

vlan mac address type learn age ports

------+----------------+--------+-----+----------+--------------------------

Supervisor:

* 199 0018.de04.6b10 dynamic Yes 0 Gi1/7

BUT THIS VLAN CONNECTED TO PORT G1/7 ITS VLAN 149 NOT 199

10XS

New Member

Re: Plz Help

Hello

6509#sh mac-address-table address 00:18:41:1d:b3:01

Legend: * - primary entry

age - seconds since last seen

n/a - not available

vlan mac address type learn age ports

------+----------------+--------+-----+----------+--------------------------

Supervisor:

* 199 0018.411d.b301 dynamic Yes 0 Gi1/7

* 197 0018.411d.b301 dynamic Yes 0 Gi1/7

what can i do now with this entry?

Hall of Fame Super Blue

Re: Plz Help

Ali

What is on port gi1/7. If it is

a) another switch you now need to log on to that switch and repeat the process ie.

sh mac-address-table address 0018.411d.b301

b) a server/PC then you need to access that server/PC and disable ipv6.

Jon

New Member

Re: Plz Help

jon my Freind

3560 switches connected to this Port.and i diabled all Ipv6 on this Switch(vlan199).....but still exist.

10xs

158
Views
5
Helpful
6
Replies