Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

poe

am i wrong or should a cat 3560 switch automaticlly do poe... if not what is the command to get that int up and running

4 ACCEPTED SOLUTIONS

Accepted Solutions

Re: poe

Which model is this. The switch should be POE enable.Paste the " show version" from the switch and let us check the model number of the switch.

It should give POE bydefault, if its POE enabled. Other wise you can go to interface config and set it up using " power inline auto" command under the interface. It should work for you.

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/12225see/cr/cli1.htm#wp6776081

HTH, Please rate if it doe.

-amit singh

Cisco Employee

Re: poe

Hi Friend,

If your 3560 is POE capable you need not do any special configuration and it will by default provide power to the device.

Cisco Catalyst 3560-24PS

24 Ethernet 10/100 ports with Power over Ethernet (PoE) and 2 SFP ports

Cisco Catalyst 3560-48PS

48 Ethernet 10/100 ports with PoE and 4 SFP ports

Cisco Catalyst 3560G-24PS

24 Ethernet 10/100/1000 ports with PoE and 4 SFP ports

Cisco Catalyst 3560G-48PS

48 Ethernet 10/100/1000 ports with PoE and 4 SFP ports

These 4 switches which has "PS" at the end of model name provides inline power.

To check some POE related configuration on switchports have a look at this link

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/12235se/scg1/swint.htm#wp1811783

HTH

Ankur

*Pls rate helpfull post

Cisco Employee

Re: poe

Hi Friend,

I am afraid your switch is not POE capable.

Ankur

Cisco Employee

Re: poe

Hi Friend,

Check the model number in the "sh version" output you pasted and it says "WS-C3560-24TS" which is not a POE switch.

The POE switch model is like "WS-C3560-24PS-S" and the POE switch model ends with "PS"

You can check the different 3560 models in this link

http://www.cisco.com/en/US/products/hw/switches/ps5528/products_data_sheet09186a00801f3d7d.html

HTH

Ankur

*Pls rate the post

9 REPLIES

Re: poe

Which model is this. The switch should be POE enable.Paste the " show version" from the switch and let us check the model number of the switch.

It should give POE bydefault, if its POE enabled. Other wise you can go to interface config and set it up using " power inline auto" command under the interface. It should work for you.

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/12225see/cr/cli1.htm#wp6776081

HTH, Please rate if it doe.

-amit singh

New Member

Re: poe

Cisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(25)SEE2, RELEA

SE SOFTWARE (fc1)

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Fri 28-Jul-06 07:19 by yenanh

Image text-base: 0x00003000, data-base: 0x00EB0F14

ROM: Bootstrap program is C3560 boot loader

BOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(25r)SEC, RELEASE SOFTWAR

E (fc4)

Switch uptime is 42 minutes

System returned to ROM by power-on

System image file is "flash:/c3560-ipbase-mz.122-25.SEE2/c3560-ipbase-mz.122-25.

SEE2.bin"

cisco WS-C3560-24TS (PowerPC405) processor (revision D0) with 118784K/12280K byt

es of memory.

Processor board ID CAT1009Z4S2

Last reset from power-on

1 Virtual Ethernet interface

24 FastEthernet interfaces

2 Gigabit Ethernet interfaces

yea it thought it should be by default and i tried the power inline auto command but it doesnt exist... do i need to up the ios ?

Cisco Employee

Re: poe

Hi Friend,

I am afraid your switch is not POE capable.

Ankur

New Member

Re: poe

how do you know?.... mostly out of curiosity because i recived it under the impression that it is

Cisco Employee

Re: poe

Hi Friend,

Check the model number in the "sh version" output you pasted and it says "WS-C3560-24TS" which is not a POE switch.

The POE switch model is like "WS-C3560-24PS-S" and the POE switch model ends with "PS"

You can check the different 3560 models in this link

http://www.cisco.com/en/US/products/hw/switches/ps5528/products_data_sheet09186a00801f3d7d.html

HTH

Ankur

*Pls rate the post

New Member

Re: poe

hmm but why whould it say poe on the switch, and have the button on the side that scrolls through and lights up the poe option?

Cisco Employee

Re: poe

Hi Friend,

Nor sure but may be the chassis which is made is quite similar for all the models and based on the integrated hardware it provides the POE.

Check this link and the model which you have does not mentions about POE.

http://www.cisco.com/en/US/products/hw/switches/ps5528/products_data_sheet09186a00801f3d7f.html

The model which supports POE is been mentioned in the chart.

Ankur

Cisco Employee

Re: poe

Hi Friend,

If your 3560 is POE capable you need not do any special configuration and it will by default provide power to the device.

Cisco Catalyst 3560-24PS

24 Ethernet 10/100 ports with Power over Ethernet (PoE) and 2 SFP ports

Cisco Catalyst 3560-48PS

48 Ethernet 10/100 ports with PoE and 4 SFP ports

Cisco Catalyst 3560G-24PS

24 Ethernet 10/100/1000 ports with PoE and 4 SFP ports

Cisco Catalyst 3560G-48PS

48 Ethernet 10/100/1000 ports with PoE and 4 SFP ports

These 4 switches which has "PS" at the end of model name provides inline power.

To check some POE related configuration on switchports have a look at this link

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/12235se/scg1/swint.htm#wp1811783

HTH

Ankur

*Pls rate helpfull post

New Member

http://www.ccnaccnplinux.com

272
Views
4
Helpful
9
Replies
CreatePlease to create content