Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Port Channel Cisco 6500 Series

Hello,

How much is the limit for the creation of PortChanel in a Core Switch 6509 and 6513?

Is there a limitation byu hardware?

Regards,

7 REPLIES
Community Member

Port Channel Cisco 6500 Series

Are you asking how many ports are allowed in a port channel?  If so, 8 is the max and they must all be of the same type (speed, duplex, etc.) and configuration (i.e. trunk or access as well as allowed VLANs).  Hope that helps.

Gold

Port Channel Cisco 6500 Series

For IOS12.2.18 you can create a maximum of 128 etherchannels, subject to the constraints listed above.

For CATos  I bleieve ther is a limitation in some chassis to 63.

Community Member

Port Channel Cisco 6500 Series

Is it the same limitation for the Nexus 7000 Series.?

Regards,

Gold

Port Channel Cisco 6500 Series

Community Member

Port Channel Cisco 6500 Series

Well, there you go, it's not the first time I've been wrong ...

Cisco Employee

Port Channel Cisco 6500 Series

I think vmiller was talking about No. of EtherChannels and you were talking about No. of ports in an Etherchannel... Both are different and you were not wrong AFAIK.

-Vijay

Community Member

Port Channel Cisco 6500 Series

Beware of trying to port-channel interfaces across different line cards. The QoS scheduling can be different and not allow a port-channel to come up. See the difference below:

sh int te7/12 cap

TenGigabitEthernet7/12

  Model:                 WS-X6716-10GE

  Type:                  10Gbase-SR

  Speed:                 10000

  Duplex:                full

  Trunk encap. type:     802.1Q

  Trunk mode:            on,off,desirable,nonegotiate

  Channel:               yes

  Broadcast suppression: percentage(0-100)

  Flowcontrol:           rx-(off,on),tx-(off,on)

  Membership:            static

  Fast Start:            yes

  QOS scheduling:        rx-(1p7q2t), tx-(1p7q4t)

  QOS queueing mode:     rx-(cos,dscp), tx-(cos,dscp)

  CoS rewrite:           yes

  ToS rewrite:           yes

  Inline power:          no

  Inline power policing: no

  SPAN:                  source/destination

  UDLD                   yes

  Link Debounce:         yes

  Link Debounce Time:    yes

  Ports-in-ASIC (Sub-port ASIC) : 9-16 (9-12)

  Remote switch uplink:  no

  Dot1x:                 yes

  Port-Security:         yes

sh int te6/1 cap

TenGigabitEthernet6/1

  Model:                 WS-X6708-10GE

  Type:                  10Gbase-SR

  Speed:                 10000

  Duplex:                full

  Trunk encap. type:     802.1Q,ISL

  Trunk mode:            on,off,desirable,nonegotiate

  Channel:               yes

  Broadcast suppression: percentage(0-100)

  Flowcontrol:           rx-(off,on),tx-(off,on)

  Membership:            static

  Fast Start:            yes

QOS scheduling:        rx-(8q4t), tx-(1p7q4t)

  QOS queueing mode:     rx-(cos,dscp), tx-(cos,dscp)

  CoS rewrite:           yes

  ToS rewrite:           yes

  Inline power:          no

  Inline power policing: no

  SPAN:                  source/destination

  UDLD                   yes

  Link Debounce:         yes

  Link Debounce Time:    yes

  Ports-in-ASIC (Sub-port ASIC) : 1,4-5,7 (1)

  Remote switch uplink:  no

  Dot1x:                 yes

  Port-Security:         yes

This is the error you will see:

%EC-SP-5-CANNOT_BUNDLE2: Te7/12 is not compatible with Te6/1 and will be suspended (qos-card types of Te7/12 do not match Te6/1)

Enter the command below on the port-channel to allow the grouping of the ports

#no mls qos channel-consistency

That being said I hope I can bundle interfaces of different optic types i.e. 10Gbase-SR and 10Gbase-LRM

508
Views
0
Helpful
7
Replies
CreatePlease to create content