Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Port Channel Settings

Hi,

Trying to setup a port channel between to Catalyst 6506's, the commands are accepted but the channeling doesn't work.

The commands I used are :

set trunk 1/1,1/2 on dot1q

set port channel 1/1,1/2 mode on

I have set these commands on both switches.

One Cat is running 8.4.5 and the other 8.5.5.

What am I doing wrong ?

Regards

Scott.

9 REPLIES

Re: Port Channel Settings

Hi

Can u give the admin qroup number and check.

Thanks

Mahmood

New Member

Re: Port Channel Settings

Hi Mahmood,

Does the admin group number have to match on both Cats ?

Scott.

Hall of Fame Super Blue

Re: Port Channel Settings

Scott

No it is only locally significant. Could you send output of

"sh channel info"

"sh trunk"

Jon

New Member

Re: Port Channel Settings

Hi Jon,

sh channel info

No ports channelling

sh trunk

* - indicates vtp domain mismatch

# - indicates dot1q-all-tagged enabled on the port

$ - indicates non-default dot1q-ethertype value

Port Mode Encapsulation Status Native vlan

-------- ----------- ------------- ------------ -----------

1/1 on dot1q trunking 1

1/2 on dot1q trunking 1

2/1 on dot1q trunking 1

2/3 on dot1q trunking 1

2/5 on dot1q trunking 1

2/7 on dot1q trunking 1

2/9 on dot1q trunking 1

2/16 on dot1q trunking 1

3/2 on dot1q trunking 1

3/3 on dot1q trunking 1

3/4 on dot1q trunking 1

3/5 on dot1q trunking 1

15/1 nonegotiate isl trunking 1

Re: Port Channel Settings

Check the configurations on 1/1 and 1/2 match exactly before you try and put them into a channel. Mismatched VLAN lists, for example, can stop them forming a channel.

The other end of the channel must also be configured "on". The "on" option stops the negotiation, so "on" will not work opposite "desirable" or "auto".

Kevin Dorrell

Luxembourg

New Member

Re: Port Channel Settings

Hi Kevin,

Have found one differaence between the 2 ports on one of the cats !!.

Port Vlans allowed and active in management domain

-------- ---------------------------------------------------------------------

1/1 1-3,5,8-9,16-22,26,32,64-66,101,104,109,116-122,126-128,204,802,901

1/2 1-3,5,8-9,16-22,26,32,64-66,101,104,109,116-122,126-128,204,802,901

Port Vlans in spanning tree forwarding state and not pruned

-------- ---------------------------------------------------------------------

1/1 1-3,5,8-9,16-22,26,32,64-66,101,104,109,116-122,126-128,204,802,901

1/2

Re: Port Channel Settings

I don't think that is the source of the problem. The allowed VLAN list are the same unless I missed something. Just that one of the links has been put in standby, which is what you would expect from Spanning Tree when you have two parallel links.

Oh, you could check that the ports actually support channel? For example, if I remember right, the ports on a 5500 sup card do not support channel. Try show port capabilities 1/1

Kevin Dorrell

Luxembourg

New Member

Re: Port Channel Settings

These are Cat6500 series (6506) with SupII & MSFCII.

Looks like it should work ?.

sh port capabilities 1/1

Model WS-X6K-SUP2-2GE

Port 1/1

Type 1000BaseSX

Auto MDIX no

AuxiliaryVlan no

Broadcast suppression percentage(0-100)

Channel yes

COPS port group 1/1-2

CoS rewrite yes

Dot1q-all-tagged yes

Dot1x yes

Duplex full

Fast start yes

Flow control receive-(off,on,desired),send-(off,on,desired)

Inline power no

Jumbo frames yes

Link debounce timer yes

Link debounce timer delay yes

Membership static,dynamic

Port ASIC group 1/1-2

Port VLAN Mapping Group: 1/1-2 Maximum Allowed Mappings: 32

Port VLAN Mapping Supported Trunk Type: dot1q

QOS scheduling rx-(1p1q4t),tx-(1p2q2t)

Security yes

SPAN source,destination

Speed 1000

Sync restart delay yes

ToS rewrite DSCP

Trunk encap type 802.1Q,ISL

Purple

Re: Port Channel Settings

USe the following. The ports and speed settings must be exactly the same on both sides

set trunk 1/1-2 on dot1q

set port channel 1/1-2 mode desirable non-silent

148
Views
0
Helpful
9
Replies