ā10-27-2010 10:10 AM - edited ā03-06-2019 01:45 PM
Hi all,
on 6509 on switch 1 port is errdisabled due to
extende: %PM_SCP-SP-2-LCP_FW_ERR_INFORM: Module 1 is experiencing the following error: Port #44 transient TX_Pb error
this is from sh log.
all others ports are ok.
when i do sh mod on device it shows
Mod Online Diag Status
---- -------------------
1 Minor Error
also when i run sh diagnostic mod 1
sh diagnostic mod 1
Current bootup diagnostic level: complete
Module 1: 48-port 10/100/1000 RJ45 EtherModule SerialNo :
Overall Diagnostic Result for Module 1 : MINOR ERROR
Diagnostic level at card bootup: complete
Test results: (. = Pass, F = Fail, U = Untested)
1) TestScratchRegister -------------> .
2) TestNonDisruptiveLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
. . . . . . . . . . . . . . . . . . . . . . . .
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
----------------------------------------------------------------------------
. . . . . . . . . F . . . . . . . . . . . . . .
3) TestLoopback:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
. . . . . . . . . . . . . . . . . . . . . . . .
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
----------------------------------------------------------------------------
. . . . . . . . . . . . . . . . . . . . . . . .
4) TestNetflowInlineRewrite:
Port 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
----------------------------------------------------------------------------
. . . . . . . . . . . . . . . . . . . . . . . .
Port 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
----------------------------------------------------------------------------
. . . . . . . . . . . . . . . . . . . . . . . .
5) TestAsicMemory ------------------> U
6) TestEobcStressPing --------------> U
7) TestFirmwareDiagStatus ----------> .
8) TestVDB -------------------------> .
Right now port is in errdisabled state and we did shut and no shut no luck.
can some one explain me this
TestNonDisruptiveLoopback: what is this and how it is permormed ?
also if singe port is errdisabled due to hardware error will that cause the minor error on module itself??
thanks
mahesh
ā10-27-2010 10:30 AM
Mahesh,
Log message indicates that mod #1 experiencing Transmit Packet Buffer (PB) error.
Details of this specific test:
I would recommend you set the diagnostic level to complete and re-seat mod #1. If the issue persist, we may need to replace it.
- Yogesh
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide