Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Port mode modified in another CLI session, ignoring [no] switchport cmd

Port mode modified in another CLI session, ignoring [no] switchport cmd

I can't find the meaning of this error message anywhere.

It occurs when doing the following:

Router#conf t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#int port 20

Router(config-if)#switch

Port-channel20: Port mode modified in another CLI session, ignoring [no] switchport cmd

Router(config-if)#

There is no other CLI session.

If I change the number 20 to 21 I have no problem at all. So I can say:

Router(config)#int port 21

Router(config-if)#switch

And I have no problem.

Also noticed that when I get the error message when configuring port-channel 20, there is the following entry in the log: - A traceback.

Sep 15 04:25:22.556 UTC: %SYS-5-CONFIG_I: Configured from console by b609207 onvty0 (10.98.75.4)

Sep 15 04:27:26.032 UTC: %CPU_MONITOR-2-NOT_RUNNING: CPU_MONITOR messages have not been sent for 30 seconds Neutrino pthread, Total CPU utilization: 15.7%, Top 3 processes/pid/CPU/tid/CPU [ios-base 16408 8.0% 8 1.9%] [kernel 1 6.5% 4 2.6%] [udp.proc 16426 0.2% 5 0.1%], Top 3 threads/pid/tid/CPU [kernel 1 4 2.6%] [kernel 1 17 2.5%] [ios-base 16408 8 1.9%]

Sep 15 04:27:26.032 UTC: %CPU_MONITOR-2-NOT_RUNNING_TB: CPU_MONITOR traceback, process/pid/tid: [ios-base 16408 8] = (libc.so+0x2E0F0) ([0:-3]s72033_rp-ipservicesk9-22-dso-b+0xFE6A0) ([23:-10]1+0x90A64) ([0:-3]libc+0x127AC)

Sep 15 04:27:26.628 UTC: %CPU_MONITOR-6-NOT_HEARD: CPU_MONITOR messages have not been heard for 30 seconds [5/0]

Sep 15 04:27:26.804 UTC: %STANDBY-6-STATECHANGE: Vlan101 Group 101 state Standby -> Active

Sep 15 04:27:26.804 UTC: %STANDBY-6-STATECHANGE: Vlan51 Group 51 state Standby -> Active

Sep 15 04:27:26.804 UTC: %STANDBY-6-STATECHANGE: Vlan90 Group 90 state Standby -> Active

Sep 15 04:27:26.804 UTC: %STANDBY-6-STATECHANGE: Vlan217 Group 217 state Standby -> Active

Sep 15 04:27:26.808 UTC: %STANDBY-6-STATECHANGE: Vlan201 Group 201 state Standby -> Active

Sep 15 04:27:26.808 UTC: %STANDBY-6-STATECHANGE: Vlan215 Group 215 state Standby -> Active

Any suggestions / help - much appreciated.

1 REPLY
New Member

Re: Port mode modified in another CLI session, ignoring [no] swi

Hi

Could you please paste the config of both ports 20 & 21

Thanks

Kev

1192
Views
0
Helpful
1
Replies