Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

ports don't up

I have two 2950 catalyst switch when i power up these switches and want to make trunk between these swithes using cross over cable the ports not up not light blink when i check status of interface

Fa0/1 is down, line protocol is down (notconnect

but when i connect this port to huawei switch port then port going up

this is screen text

Cisco Internetwork Operating System Software

IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA5, RELEASE SOFTWARE                                              (fc1)

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Wed 13-Jul-05 22:09 by antonino

Image text-base: 0x80010000, data-base: 0x80566000

Initializing flashfs...

flashfs[1]: 358 files, 4 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 7741440

flashfs[1]: Bytes used: 4668928

flashfs[1]: Bytes available: 3072512

flashfs[1]: flashfs fsck took 8 seconds.

flashfs[1]: Initialization complete.

Done initializing flashfs.

POST: System Board Test : Passed

POST: Ethernet Controller Test : Passed

ASIC Initialization Passed

POST: FRONT-END LOOPBACK TEST : Passed

cisco WS-C2950T-24 (RC32300) processor (revision R0) with 21025K bytes of memory                                             .

Processor board ID FOC0942Z2FJ

Last reset from system-reset

Running Enhanced Image

24 FastEthernet/IEEE 802.3 interface(s)

2 Gigabit Ethernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:15:F9:3F:2A:C0

Motherboard assembly number: 73-6114-10

Power supply part number: 34-0965-01

Motherboard serial number: FOC09412WTL

Power supply serial number: DAB0937FZAG

Model revision number: R0

Motherboard revision number: A0

Model number: WS-C2950T-24

System serial number: FOC0942Z2FJ

Press RETURN to get started!

00:00:16: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan

00:00:18: %SYS-5-CONFIG_I: Configured from memory by console

00:00:18: %SYS-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA5, RELEASE SOFTWARE                                              (fc1)

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Wed 13-Jul-05 22:09 by antonino

00:00:18: %SNMP-5-COLDSTART: SNMP agent on host switch2 is undergoing a cold sta                                             rt

00:00:19: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively do                                             wn

00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state t

plz help

3 REPLIES
Purple

ports don't up

Hi,

Can you post the output of sh int f0/1 switchport  and sh int f0/1 status

Regards

Alain

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.
Purple

ports don't up

  I would check to make sure you are actually using a crossover cable and not a straight .

New Member

ports don't up

Hi

        solved my swith ports are loose

thanks

140
Views
0
Helpful
3
Replies
CreatePlease login to create content