I have a Cisco Catalyst WS-6509 switch with the following problem:
Each time the switch reloads, it adds this in the config to all my POE interfaces:
interface FastEthernet9/1 no ip address switchport switchport access vlan xx switchport mode access power inline auto max 7000 end
After a reload I always have to perform a no power inline command, to remove the 7000 milli-watts limit. Even tough I run the copy run start after this, each time it reloads, it shows up again.
Very annoying when you have POE devices connected which need more than 7000 milli-watts.
Cisco Internetwork Operating System Software IOS (tm) c6sup2_rp Software (c6sup2_rp-PK9S-M), Version 12.2(18)SXD6, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Wed 17-Aug-05 18:56 by evmiller Image text-base: 0x4002100C, data-base: 0x422F0000
ROM: System Bootstrap, Version 12.1(11r)E1, RELEASE SOFTWARE (fc1) BOOTLDR: c6sup2_rp Software (c6sup2_rp-PK9S-M), Version 12.2(18)SXD6, RELEASE SOFTWARE (fc1)
HSsec-CORE-S01 uptime is 3 hours, 25 minutes Time since HSsec-CORE-S01 switched to active is 3 hours, 24 minutes System returned to ROM by power-on (SP by power-on) System restarted at 07:12:50 BRUSSELS Fri Oct 10 2014 System image file is "sup-bootflash:/c6k222-pk9s-mz.122-18.SXD6.bin"
This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to email@example.com.
cisco WS-C6509 (R7000) processor (revision 2.0) with 458752K/65536K bytes of memory. Processor board ID SCA05020CTK R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache Last reset from power-on X.25 software, Version 3.0.0. Bridging software. 9 Virtual Ethernet/IEEE 802.3 interface(s) 48 FastEthernet/IEEE 802.3 interface(s) 252 Gigabit Ethernet/IEEE 802.3 interface(s) 381K bytes of non-volatile configuration memory.
32768K bytes of Flash internal SIMM (Sector size 512K). Configuration register is 0x2102
We are pleased to announce availability of Beta software for 16.6.3.
16.6.3 will be the second rebuild on the 16.6 release train targeted
towards Catalyst 9500/9400/9300/3850/3650 switching platforms. We are
looking for early feedback from customers befor...
Introduction Featured Speakers Luis Espejel is the Telecommunications
Manager of IENova, an Oil & Gas company. Currently he works with Cisco
IOS® and Cisco IOS XE platforms, and NX to some extent. He has also
worked as a Senior Engineer with the Routing P...
In this session you can learn more about Layer 3 multicast and the best
practices to identify possible threats and take security measures. It
provides an overview of basic multicast, the best security practices for
use of this technology, and recommendati...