Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Problem between WS-X6748-GE-TX and WS-F6700-CFC

Hello,

I have installed two WS-X6748-GE-TX card with hardware version 2.5 with a sub-module WS-F6700-CFC. With hardware version 2.4 works right but with hardware version 2.5 doesn?t recognize this cards. Is there incompatibility with this version and hardware?

Thank you

I attach show tech

CORE_1#sh module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1028UGDA

2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL10425TX5

3 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL10425TV1

5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1021PGA5

6 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL1025RS34

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0017.94dc.8ed8 to 0017.94dc.8f07 2.4 12.2(14r)S5 12.2(17d)SXB Ok

2 0019.aa74.90e0 to 0019.aa74.910f 2.5 12.2(14r)S5 12.2(17d)SXB Other

3 0019.56ef.e1e0 to 0019.56ef.e20f 2.5 12.2(14r)S5 12.2(17d)SXB Other

5 0013.c347.0d14 to 0013.c347.0d17 5.2 8.4(2) 12.2(17d)SXB Ok

6 0013.c347.1628 to 0013.c347.162b 5.2 8.4(2) 12.2(17d)SXB Ok

Mod Sub-Module Model Serial Hw Status

--- --------------------------- ------------------ ------------ ------- -------

1 Centralized Forwarding Card WS-F6700-CFC SAL1025S0M3 2.0 Ok

2 Centralized Forwarding Card WS-F6700-CFC SAL104150Y7 2.1 Other

3 Centralized Forwarding Card WS-F6700-CFC SAL10403L7C 2.1 Other

5 Policy Feature Card 3 WS-F6K-PFC3B SAL1021P6W0 2.3 Ok

5 MSFC3 Daughterboard WS-SUP720 SAL1020NMGW 2.5 Ok

6 Policy Feature Card 3 WS-F6K-PFC3B SAL1023R0FG 2.3 Ok

6 MSFC3 Daughterboard WS-SUP720 SAL1023QF6Y 2.5 Ok

Mod Online Diag Status

--- -------------------

1 Pass

2 Unknown

3 Unknown

5 Pass

6 Pass

2 REPLIES
Silver

Re: Problem between WS-X6748-GE-TX and WS-F6700-CFC

For all WS-X67xx modules, the daughter cards are for the baseboard only. When the baseboard has a CFC or DFC3 daughter card installed, you must add the daughter card power to the baseboard power to get the total slot power. For all other modules that support a mandatory or optional daughter card, you must add the daughter card power to the baseboard power to get the total slot power.

New Member

Re: Problem between WS-X6748-GE-TX and WS-F6700-CFC

Ok, if I've understood, perhaps the problem is a power issue ?

This chassis has two 3000W AC PS installed, adding all power consume (only for 6748):

7Amp from baseboards plus 0,75 from gaughter are 7,75Amp

In other hands, the partial power from three 6748 is more than 23 Amp. Both 3000W PS is able to supply this power ?

459
Views
0
Helpful
2
Replies
CreatePlease to create content