Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Problem image in Cisco access point 2600

IOS Bootloader - Starting system.

flash is writable

FLASH CHIP:  Numonyx Mirrorbit (0089)

Xmodem file system is available.

flashfs[0]: 37 files, 9 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31997952

flashfs[0]: Bytes used: 8958976

flashfs[0]: Bytes available: 23038976

flashfs[0]: flashfs fsck took 15 seconds.

Reading cookie from SEEPROM

Base Ethernet MAC address: 7c:ad:74:db:4d:59

Ethernet speed is 1000 Mb - FULL Duplex

Loading "flash:/ap3g2-k9w8-mx.152-2.JB/ap3g2-k9w8-xx.152-2.JB"...flash:/ap3g2-k9

w8-mx.152-2.JB/ap3g2-k9w8-xx.152-2.JB: no such file or directory

Error loading "flash:/ap3g2-k9w8-mx.152-2.JB/ap3g2-k9w8-xx.152-2.JB"

Interrupt within 5 seconds to abort boot process.

Boot process failed...

The system is unable to boot automatically.  The BOOT

environment variable needs to be set to a bootable

image.

Loading "flash:/ap3g2-k9w8-mx.152-2.JB/ap3g2-k9w8-xx.152-2.JB"...flash:/ap3g2-k9

w8-mx.152-2.JB/ap3g2-k9w8-xx.152-2.JB: no such file or directory

Error loading "flash:/ap3g2-k9w8-mx.152-2.JB/ap3g2-k9w8-xx.152-2.JB"

Interrupt within 5 seconds to abort boot process.

Boot process failed...

The system is unable to boot automatically.  The BOOT

environment variable needs to be set to a bootable

image.

C2600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JA1, RELEASE SOFTWARE (f

c1)

Technical Support: http://www.cisco.com/techsupport

Compiled Wed 30-May-12 03:34 by binugopa

ap:

ap:

ap:

how to reset to factory settings ?

2 ACCEPTED SOLUTIONS

Accepted Solutions

Problem image in Cisco access point 2600

Hello

Here's the procedure you need:

Resetting the Device to Default Settings

If you need to start over during the initial setup process, you can reset the access point to factory default settings.

Resetting to Default Settings Using the MODE Button

Follow these steps to reset the access point to factory default settings using the access point MODE button:


Step 1 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.

Step 2 Press and hold the MODE button while you reconnect power to the access point.

Step 3 Hold the MODE button until the Status LED turns amber (approximately 1 to 2 seconds), and release the button. All access point settings return to factory defaults.


http://www.cisco.com/en/US/docs/wireless/access_point/12.4.25d.JA/Configuration/guide/scg12.4.25d.JA-chap4-first.html#wp1034993

Regards.

Wilson B.

VIP Purple

Problem image in Cisco access point 2600

this post should help you as it describe what you have to do

https://supportforums.cisco.com/thread/2045805

HTH

Rasika

2 REPLIES

Problem image in Cisco access point 2600

Hello

Here's the procedure you need:

Resetting the Device to Default Settings

If you need to start over during the initial setup process, you can reset the access point to factory default settings.

Resetting to Default Settings Using the MODE Button

Follow these steps to reset the access point to factory default settings using the access point MODE button:


Step 1 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.

Step 2 Press and hold the MODE button while you reconnect power to the access point.

Step 3 Hold the MODE button until the Status LED turns amber (approximately 1 to 2 seconds), and release the button. All access point settings return to factory defaults.


http://www.cisco.com/en/US/docs/wireless/access_point/12.4.25d.JA/Configuration/guide/scg12.4.25d.JA-chap4-first.html#wp1034993

Regards.

Wilson B.

VIP Purple

Problem image in Cisco access point 2600

this post should help you as it describe what you have to do

https://supportforums.cisco.com/thread/2045805

HTH

Rasika

3679
Views
10
Helpful
2
Replies
CreatePlease login to create content