Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

PSU upgrade to WS-CAC-6000W

I am having 6513 running on "s72033-psv-mz.122-17d.SXB1.bin"

It has the following modules...

Mod Ports Card Type                              Model             

--- ----- -------------------------------------- ------------------

  1   16  SFM-capable 16 port 1000mb GBIC        WS-X6516A-GBIC    

  2   48  48 port 10/100/1000mb EtherModule       WS-X6148-GE-TX    

  3   48  48 port 10/100/1000mb EtherModule       WS-X6148-GE-TX    

  4   48  48 port 10/100/1000mb EtherModule       WS-X6148V-GE-TX   

  7    2          Supervisor Engine 720 (Active)         WS-SUP720-3B 

I am going to upgrade the existing PSU to "WS-CAC-6000W"

I have following concern that I want to confirm

1. As per the link..

   http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/product_data_sheet0900aecd801c5c84.html

    It is suggested to upgrade the image to 12.2(17d)SXB.

    Is it feasible to use existing ios "12.2(17d)SXB1" with "WS-CAC-6000W". Would there be an issue with kind of power mode I am using.

  I don't want to reboot my switch.

2. With kind of modules I am using, would there be any outage to any module if I replace PSU one by one.

     Will these modules survive with one PSU.

   I have some servers attached to this one switch and I don't want to have any kind of outage.

Existing PSU....

#show power

will provide soon

Also let me know for any specific output required here.

Thanx

Everyone's tags (3)
5 REPLIES
New Member

PSU upgrade to WS-CAC-6000W

01>sh power
system power redundancy mode = redundant
system power total =     2331.00 Watts (55.50 Amps @ 42V)
system power used =      1378.02 Watts (32.81 Amps @ 42V)
system power available =  952.98 Watts (22.69 Amps @ 42V)
                         Power-Capacity PS-Fan Output Oper
PS   Type               Watts   A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1    WS-CAC-2500W       2331.00 55.50  OK     OK     on
2    WS-CAC-2500W       2331.00 55.50  OK     OK     on
                         Pwr-Allocated  Oper
Fan  Type               Watts   A @42V State
---- ------------------ ------- ------ -----
1    WS-C6K-13SLT-FAN2   298.20  7.10  OK
                         Pwr-Requested  Pwr-Allocated  Admin Oper
Slot Card-Type          Watts   A @42V Watts   A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1    WS-X6516A-GBIC      152.04  3.62   152.04  3.62  on    on
2    WS-X6148-GE-TX      103.74  2.47   103.74  2.47  on    on
3    WS-X6148-GE-TX      103.74  2.47   103.74  2.47  on    on
4    WS-X6148V-GE-TX     121.38  2.89   121.38  2.89  on    on
7    WS-SUP720-3B        282.24  6.72   282.24  6.72  on    on
8                          -     -      282.24  6.72  -     -
                         Inline         Inline         Inline
                         Pwr-Requested  Pwr-Allocated  Local-Pwr-Pool
Slot Card-Type          Watts   A @42V Watts   A @42V Watts   A @42V
---- ------------------ ------- ------ ------- ------ ------- ------
4    WS-F6K-VPWR-GE        -     -        -     -       34.44  0.82

Green

PSU upgrade to WS-CAC-6000W

Avrind,

You need to read the spec again.

Software Compatibility

Cisco IOS® Software Release:

• 12.2(18)SXD and later

• 12.1E: not supported

Cisco Catalyst OS:

• 8.4(1)

You need to upgrade to 12.2.18SXD or later to support this PUSU.

You will need a reload to use the new IOS.

A mantenance downtime window will be required.

Regards,
Alex.
Please rate useful posts.

Regards, Alex. Please rate useful posts.
New Member

PSU upgrade to WS-CAC-6000W

Alex,

Yes, it is clearly mentioned to upgarde the IOS however I don't want to reboot the switch.

I don't have enough time to get necessary approval thats reason,I don't want to upgrade it.

Currently it is running in rundandent mode and I have seen that someone upgraded the PSU with same image I have.

That image forced it to be in combined mode.

https://supportforums.cisco.com/message/585129#585129

I can understand that that will surely hit me too. 

1. I cann't use the redundent mode

2.  If  I continue with combined mode, it will affect in future.

As links says ... https://supportforums.cisco.com/thread/2070718

"Power supply is removed with redundancy disabled(combined mode)

• System log and syslog messages are generated.

• System power is decreased to the power capability of one supply.

• If there is not enough power for all previously powered-up modules,

some modules are powered down and marked as power-deny

in the show power oper state field."

Purple

PSU upgrade to WS-CAC-6000W

  It probably won't even recognize it if you don't upgrade the code first.

New Member

PSU upgrade to WS-CAC-6000W

Thanks my friend.

288
Views
0
Helpful
5
Replies
CreatePlease login to create content