11-16-2011 08:07 PM - edited 03-07-2019 03:26 AM
Hello All,
I am in need of some asistance, I have searched for days one forums and Google and am unable to find a sample config that doesnt use autoqos.
I need to enable QOS on a 6513 that i am using as a access switch.( loaded with
WS-X6148-45AF). I am running SUP2MFSC2 with IOS and autoqos is not supported.
below is my IOS version and my requirements.
Requirements:
Trust CoS and DiffServ Value coming from Avaya equipments
DiffServ=46 for Audio and DiffServ=26 for Signaling
CoS=5 for Audio and CoS=3 for Signaling
I am running the following IOS:
IOS (tm) s222_rp Software (s222_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF17b, RELEASE SOFTWARE (fc1)
Sample Port config:( Vlan 709 = Data,Vlan 809=VOIP)
switchport
switchport access vlan 709
switchport mode access
switchport voice vlan 809
no ip address
spanning-tree portfast
end
show mls qos
QoS is enabled globally
QoS ip packet dscp rewrite enabled globally
Input mode for GRE Tunnel is Pipe mode
Vlan or Portchannel(Multi-Earl) policies supported: Yes
Egress policies supported: No
----- Module [2] -----
QoS global counters:
Total packets: 33034
IP shortcut packets: 0
Packets dropped by policing: 0
IP packets with TOS changed by policing: 2349
IP packets with COS changed by policing: 30
Non-IP packets with COS changed by policing: 0
sho mls qos maps
Normal Burst Policed-dscp map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
-------------------------------------
0 : 00 01 02 03 04 05 06 07 08 09
1 : 10 11 12 13 14 15 16 17 18 19
2 : 20 21 22 23 24 25 26 27 28 29
3 : 30 31 32 33 34 35 36 37 38 39
4 : 40 41 42 43 44 45 46 47 48 49
5 : 50 51 52 53 54 55 56 57 58 59
6 : 60 61 62 63
Maximum Burst Policed-dscp map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
-------------------------------------
0 : 00 01 02 03 04 05 06 07 08 09
1 : 10 11 12 13 14 15 16 17 18 19
2 : 20 21 22 23 24 25 26 27 28 29
3 : 30 31 32 33 34 35 36 37 38 39
4 : 40 41 42 43 44 45 46 47 48 49
5 : 50 51 52 53 54 55 56 57 58 59
6 : 60 61 62 63
Dscp-cos map: (dscp= d1d2)
d1 : d2 0 1 2 3 4 5 6 7 8 9
-------------------------------------
0 : 00 00 00 00 00 00 00 00 01 01
1 : 01 01 01 01 01 01 02 02 02 02
2 : 02 02 02 02 03 03 03 03 03 03
3 : 03 03 04 04 04 04 04 04 04 04
4 : 05 05 05 05 05 05 05 05 06 06
5 : 06 06 06 06 06 06 07 07 07 07
6 : 07 07 07 07
Cos-dscp map:
cos: 0 1 2 3 4 5 6 7
------------------------------------
dscp: 0 6 16 26 32 46 48 56
IpPrecedence-dscp map:
ipprec: 0 1 2 3 4 5 6 7
------------------------------------
dscp: 0 8 16 24 32 40 48 56
Your help will be greatly appreciated.
Regards,
Brad
12-14-2011 09:40 AM
Hello Bradford,
I believe this type of card does support "mls qos trust dscp" under the interface config. Can you give that a try?
Fabienne
TAC
05-30-2012 03:26 PM
Hi,
I was wondering if you found a solution? I am in the same boat as you and can't find anything on the Avaya site besides the autoqos.
Thanks,
James
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: