Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

QOS 6513 SUP2 AVAYA VOIP

Hello All,

I am in need of some asistance, I have searched for days one forums and Google and am unable to find a sample config that doesnt use autoqos.

I need to enable QOS on a 6513 that i am using as a access switch.( loaded with

WS-X6148-45AF).  I am running SUP2MFSC2 with IOS and autoqos is not supported. 

below is my IOS version and my requirements.

Requirements:

Trust CoS and DiffServ Value coming from Avaya equipments

DiffServ=46 for Audio and DiffServ=26 for Signaling

CoS=5 for Audio and CoS=3 for Signaling

I am running the following IOS:

IOS (tm) s222_rp Software (s222_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF17b, RELEASE SOFTWARE (fc1)

Sample Port config:( Vlan 709 = Data,Vlan 809=VOIP)

switchport

switchport access vlan 709

  switchport mode access

switchport voice vlan 809

no ip address

spanning-tree portfast

end

show mls qos

  QoS is enabled globally

  QoS ip packet dscp rewrite enabled globally

  Input mode for GRE Tunnel is Pipe mode

  Vlan or Portchannel(Multi-Earl) policies supported: Yes

  Egress policies supported: No

----- Module [2] -----

  QoS global counters:

    Total packets: 33034

    IP shortcut packets: 0

    Packets dropped by policing: 0

    IP packets with TOS changed by policing: 2349

    IP packets with COS changed by policing: 30

    Non-IP packets with COS changed by policing: 0

sho mls qos maps

   Normal Burst Policed-dscp map:                                  (dscp= d1d2)

     d1 :  d2 0  1  2  3  4  5  6  7  8  9

     -------------------------------------

      0 :    00 01 02 03 04 05 06 07 08 09

      1 :    10 11 12 13 14 15 16 17 18 19

      2 :    20 21 22 23 24 25 26 27 28 29

      3 :    30 31 32 33 34 35 36 37 38 39

      4 :    40 41 42 43 44 45 46 47 48 49

      5 :    50 51 52 53 54 55 56 57 58 59

      6 :    60 61 62 63

   Maximum Burst Policed-dscp map:                                  (dscp= d1d2)

     d1 :  d2 0  1  2  3  4  5  6  7  8  9

     -------------------------------------

      0 :    00 01 02 03 04 05 06 07 08 09

      1 :    10 11 12 13 14 15 16 17 18 19

      2 :    20 21 22 23 24 25 26 27 28 29

      3 :    30 31 32 33 34 35 36 37 38 39

      4 :    40 41 42 43 44 45 46 47 48 49

      5 :    50 51 52 53 54 55 56 57 58 59

      6 :    60 61 62 63

   Dscp-cos map:                                  (dscp= d1d2)

     d1 :  d2 0  1  2  3  4  5  6  7  8  9

     -------------------------------------

      0 :    00 00 00 00 00 00 00 00 01 01

      1 :    01 01 01 01 01 01 02 02 02 02

      2 :    02 02 02 02 03 03 03 03 03 03

      3 :    03 03 04 04 04 04 04 04 04 04

      4 :    05 05 05 05 05 05 05 05 06 06

      5 :    06 06 06 06 06 06 07 07 07 07

      6 :    07 07 07 07

   Cos-dscp map:

         cos:   0  1  2  3  4  5  6  7

     ------------------------------------

        dscp:   0  6 16 26 32 46 48 56

   IpPrecedence-dscp map:

      ipprec:   0  1  2  3  4  5  6  7

     ------------------------------------

        dscp:   0  8 16 24 32 40 48 56

Your help will be greatly appreciated.

Regards,

Brad

Everyone's tags (2)
2 REPLIES
Cisco Employee

QOS 6513 SUP2 AVAYA VOIP

Hello Bradford,

I believe this type of card does support "mls qos trust dscp" under the interface config. Can you give that a try?

Fabienne

TAC

New Member

QOS 6513 SUP2 AVAYA VOIP

Hi,

I was wondering if you found a solution?  I am in the same boat as you and can't find anything on the Avaya site besides the autoqos.

Thanks,

James

750
Views
0
Helpful
2
Replies
CreatePlease to create content