Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

QoS error on 6513

I am having an issue on my 6513 where I can install a QoS policy. I just can't apply the policy to an interfacce. I have tried this a few times, but keep getting the same error.

I input this:

mls qos map policed-dscp normal-burst 24 26 to 8

mls qos map dscp-cos 10 to 0

mls qos map cos-dscp 0 8 16 24 32 46 48 56

no mls qos marking statistics

mls qos

!

class-map match-any SIGNAL

match access-group name SIGNAL

match ip dscp cs3

match ip dscp af31

class-map match-any VOICE

match ip dscp ef

class-map match-any KNOWN

match any

class-map match-any UNKNOWN

match any

!

!

policy-map PHONE+PC

class VOICE

police cir 128000 bc 8000 be 8000 conform-action set-dscp-transmit ef

exceed-action drop violate-action drop

class SIGNAL

police cir 32000 bc 8000 be 8000 conform-action set-dscp-transmit cs3

exceed-action policed-dscp-transmit violate-action policed-dscp-transmit

class class-default

set dscp default

!

policy-map KNOWN

class KNOWN

set dscp af21

!

policy-map UNKNOWN

class UNKNOWN

set dscp default

When I go to my gi1/1 port and try to apply the policy I get this error:

6513(config)#int g1/1

6513(config-if)#Service-policy input PHONE+PC

QoS: Match criteria in class SIGNAL on GigabitEthernet1/1 cannot simultaneously have match

dscp | precedence | exp and match ACL

QoS: policy PHONE+PC actions for class SIGNAL are not supported on GigabitEthernet1/1

QoS: Match criteria in class SIGNAL on GigabitEthernet1/1 cannot simultaneously have match

dscp | precedence | exp and match ACL

QoS: Match criteria in class SIGNAL on GigabitEthernet1/1 cannot simultaneously have match

dscp | precedence | exp and match ACL

I can apply this policy just fine on our 4506 and 4510 switches... just not on any of our 6500s. Am I missing something in the 6509 or 6513 config? Any ideas?

Thanks,

Chris

3 REPLIES
New Member

Re: QoS error on 6513

Chris,

Can you let us know what version of code and supervisor you are running?

There is a restriction before 12.2(18)SXE that you cannot have more than one match statement in a class-map.

From the config guide:

With Release 12.2(18)SXE and later releases, PFC QoS supports multiple match criteria in class maps configured with the match-any keywords.

Configuration guide location:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SXF/native/configuration/guide/qos.html

If you are past this code, let us know and we can take it from there.

Regards,

John Gill

New Member

Re: QoS error on 6513

Here's a show ver:

6513#sh ver

Cisco Internetwork Operating System Software

IOS (tm) s72033_rp Software (s72033_rp-PSV-M), Version 12.2(18)SXD6, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Wed 17-Aug-05 17:34 by evmiller

Image text-base: 0x4002100C, data-base: 0x42040000

ROM: System Bootstrap, Version 12.2(14r)S9, RELEASE SOFTWARE (fc1)

BOOTLDR: s72033_rp Software (s72033_rp-PSV-M), Version 12.2(18)SXD6, RELEASE SOFTWARE (fc1)

Denver_6513 uptime is 12 weeks, 4 days, 10 hours, 12 minutes

Time since Denver_6513 switched to active is 12 weeks, 4 days, 13 hours, 35 minutes

System returned to ROM by power-on (SP by power-on)

System restarted at 00:45:37 MST Sun Feb 24 2008

System image file is "disk0:s72033-psv-mz.122-18.SXD6.bin"

cisco WS-C6513 (R7000) processor (revision 1.0) with 458720K/65536K bytes of memory.

Processor board ID SAL0749QAUW

SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache

Last reset from power-on

X.25 software, Version 3.0.0.

Bridging software.

27 Virtual Ethernet/IEEE 802.3 interface(s)

484 Gigabit Ethernet/IEEE 802.3 interface(s)

1917K bytes of non-volatile configuration memory.

8192K bytes of packet buffer memory.

65536K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x2102

New Member

Re: QoS error on 6513

Chris,

Your code will not let you use the multiple match statements, you need to upgrade to 12.2(18)SXE or later to get this functionality.

I tried this on a lab switch of my own and no errors:

class-map match-any SIGNAL

match access-group name SIGNAL

match ip dscp cs3

match ip dscp af31

!

!

policy-map matchall

class matchall

set dscp cs1

policy-map PHONE+PC

class SIGNAL

police cir 32000 bc 8000 be 8000 conform-action set-dscp-transmit cs3 exceed-action drop violate-action drop

6500(config)#int gi 5/1

6500(config-if)#service-policy input PHONE+PC

6500#sh policy-map int

GigabitEthernet5/1

Service-policy input: PHONE+PC

class-map: SIGNAL (match-any)

Match: access-group name SIGNAL

Match: ip dscp cs3

Match: ip dscp af31

police :

32000 bps 8000 limit 8000 extended limit

Earl in slot 5 :

0 bytes

5 minute offered rate 0 bps

aggregate-forwarded 0 bytes action: set-dscp-transmit

exceeded 0 bytes action: drop

aggregate-forward 0 bps exceed 0 bps

Class-map: class-default (match-any)

0 packets, 0 bytes

5 minute offered rate 0 bps, drop rate 0 bps

Match: any

228
Views
0
Helpful
3
Replies
CreatePlease to create content