08-15-2014 01:01 AM - edited 03-07-2019 08:23 PM
Dear Experts,
I'm looking for sample configuration documents for configuring QoS on Sup2T with IOS 15.1 SY.
Cuold you point me to appropriate documents please.
S
08-15-2014 01:22 AM
Hi,
Here is good document on Sup-2T QOS architecture
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/white_paper_c11-652042.html
HTH
10-14-2014 07:04 AM
Hi
From the above URL
The PFC3-based mls qos global command is replaced with the auto qos default global command, which is used for enabling QoS just at the port level and not at the PFC level
7.2 Default State of Port Level QoS
My question is
Auto QoS is CoS based. We require the ports (uplink ports) to possibly pass DSCP transperently, that is possibly received from access switches. How could this be acheived. Sample QoS configurations, for 6500-E, sup2T, ios15.1SY would be greatley appriciated.
10-24-2014 05:12 AM
Port is configurable with QoS service policy.
Unable to configure VLAN with QoS service policy.
6506E-2T#
!
interface Vlan112
ip address 10.112.112.1 255.255.255.0
end
6506E-2T(config)#int vlan 112
6506E-2T(config-if)#service-policy type lan-queuing input INGRESS-1P7Q2T
HQM not supported interface Vlan112MQC features are not supported for this interface
Anyone come accross this please?
platform qos vlan-based is not available in config listing.
(config)#platform qos ?
10g-only qos pure 10G mode
aggregate-policer Named aggregate policer
marking marking keyword
police police keyword
protocol protocol keyword
queueing-only queueing-only (no QoS rewrite, no policing)
rewrite packet qos rewrite enable/disable
service-policy global policy map name
statistics-export qos statistics data export
Testing on 6506-E, Sup2T, IOS15.1SY.
SS
08-20-2014 03:11 AM
I've also used the following documents to prepare the configs.
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/15-0SY/configuration/guide/15_0_sy_swcg/qos_policy_based_queueing.html
and
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Campus/Borderless_Campus_Network_1-0/Borderless_Campus_1-0_Design_Guide/BN_Campus_QoS.html
I have questions on when to set auto QoS, how to ensure DSCP is read, when physical interface (TE1/1) is applied with service policy, What happens to many VLANs (some with L3and others with L2 at switch level). etc...
08-20-2014 03:27 AM
6506-E, Sup2T, IOS 15.1(1)SY1
==============================
What are the Show commands to identify
What QoS markings arrive at the ingress port on core 6500-E
What QoS markings set on egress port on core 6506-E
What happen to CoS markings on egress? on ingress?
How to set a port to trust DSCP? and confirm this?
What happens to a traffic marked with Cos that arrives on a DSCP trust port?
I'm trying to utlise these sh commands too.
show platform qos, and show queueing interface tengigabitethernet 1/1
1P7Q4T
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: