Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Redistribute Multiple Route Maps into EIGRP

I am doing some lab trials with GNS3 to try and work out a better method of redistributing static routes into our network.

What I want to do is redistribute multiple route-maps into EIGRP.  Below is a run down of what I have setup so far.

I have setup the default route 0.0.0.0 0.0.0.0 Null0 on both R1 and R3

I have setup ip route ip route 10.10.5.0 255.255.255.0 10.33.4.6 and ip route 203.20.20.0 255.255.255.0 10.33.4.6 on R1

R4 has static routes back into the network

Capture.PNG

What I have setup in my lap is 3 core routers and I have R1 and R3 setup with route maps redistributing the default route as below -

#####R1#####

router eigrp 10

redistribute static route-map redist-default-eigrp

!

ip access-list standard redist-default-eigrp

permit 0.0.0.0

!

route-map redist-default-eigrp permit 10

match ip address redist-default-eigrp

set metric 1000000 10 255 1 1500

!

#####R3#######

router eigrp 10

redistribute static route-map redist-default-eigrp

!

ip access-list standard redist-default-eigrp

permit 0.0.0.0

!

route-map redist-default-eigrp permit 10

match ip address redist-default-eigrp

set metric 100 100000 1 1 1500

The above works as expected the route redistributed from R1 is of high preference and R2 sees it this way.

Now what I want to do is add another route map that will distribute the static routes require to get to R4, so I have created the following configurations

###########R1#############

ip access-list standard redist-ract-static

permit 10.10.5.0 0.0.0.255

permit 203.20.20.0 0.0.0.255

!

route-map redist-ract-static permit 10

match ip address redist-ract-static

set metric 10000 10 255 1 1500

The problem I have is that when I do the following command it removes the existing redistribution map from eigrp.

router eigrp 10

redistribute static route-map redist-ract-static

Is there a way to redistribute multiple route maps into EIGRP?

Any help greatly appreciated.

Isaac

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Redistribute Multiple Route Maps into EIGRP

Hello Isaac,

given a  specific source protocol static in your case only a single route-map can be used.

However, route-maps can be made of multiple blocks or clauses you would need a single route-map but with two blocks.

When creating the second route-map block you need to use the same name and to give a different number

route-map xxx permit 10

! match

! set

route-map xxx permit 20

! match

! set

In this way the router will be configured for considering a route-map made of two clauses

Hope to help

Giuseppe

3 REPLIES
Hall of Fame Super Silver

Redistribute Multiple Route Maps into EIGRP

Hello Isaac,

given a  specific source protocol static in your case only a single route-map can be used.

However, route-maps can be made of multiple blocks or clauses you would need a single route-map but with two blocks.

When creating the second route-map block you need to use the same name and to give a different number

route-map xxx permit 10

! match

! set

route-map xxx permit 20

! match

! set

In this way the router will be configured for considering a route-map made of two clauses

Hope to help

Giuseppe

New Member

Re: Redistribute Multiple Route Maps into EIGRP

Thanks for the reply Guiseppe.

I will have a look at doing it this way, which will work for sure.

Is there any other way of injecting static routes into EIGRP or have I chosed the right method?

UPDATED

This is exactly what I was after.

Set it up in GNS3 today and works a treat.

Thanks again Guiseppe.

Cheers,

Isaac

New Member

Redistribute Multiple Route Maps into EIGRP

Just an update, put this into production this week.

Worked a treat.

ROUTER1

no redistribute static metric 10000 10 255 1 1500

ip access-list standard redist-default-eigrp

permit 0.0.0.0

!

ip access-list standard redist-ract-eigrp

permit 10.10.5.0 0.0.0.255

permit 10.150.10.0 0.0.0.255

permit 10.150.60.20 0.0.0.0

permit 203.20.20.0 0.0.0.255

permit 203.20.21.0 0.0.0.255

permit 203.20.22.0 0.0.0.255

permit 203.20.23.0 0.0.0.255

!

route-map redist-static-eigrp permit 10

match ip address redist-default-eigrp

set metric 1000000 10 255 1 1500

!

route-map redist-static-eigrp permit 20

match ip address redist-ract-eigrp

set metric 1000000 10 255 1 1500

!

router eigrp 10

redistribute static route-map redist-static-eigrp

ROUTER3

ip access-list standard redist-static-eigrp

permit 0.0.0.0

!

route-map redist-static-eigrp permit 10

match ip address redist-default-eigrp

set metric 10 1000000 1 1 1500

!

router eigrp 10

redistribute static route-map redist-static-eigrp

435
Views
0
Helpful
3
Replies