Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Redistributing EIGRP using route-map Nexus 5596 L3

Hi All:

this is a Nexus 5596 L3 with the latest code:

It looks like the deny statement is not working as I can see  all routes I am redistributing. I even did a deny on a specific route and I still see it in the routing table on another router in the autonomous system.

The same below works fine on IOS platform

ant help appreciated before I open a case.

Thanks

ip access-list ACL-ALLOW-STATIC-TO-EIGRP

  10 remark test

  20 remark test2

  30 permit ip 55.55.55.1/32 any

  40 permit ip 55.55.65.1/32 any

  50 permit ip 55.55.75.1/24 any

  60 deny ip any any

route-map ROUTEMAP-ALLOW-STATIC-TO-EIGRP permit 10

  match ip address ACL-ALLOW-STATIC-TO-EIGRP

route-map ROUTEMAP-ALLOW-STATIC-TO-EIGRP deny 20

router eigrp client

  autonomous-system 1

   redistribute static route-map ROUTEMAP-ALLOW-STATIC-TO-EIGRP

  default-information originate

ip route 0.0.0.0/0 10.121.1.1

ip route 55.55.55.1/32 10.121.1.18 name test1

ip route 55.55.65.1/32 10.121.1.18 name test2

ip route 55.55.75.1/32 10.121.1.18 name test3

ip route 55.55.85.1/32 10.121.1.18 name test4

ip route 55.55.95.1/32 10.121.1.18 name test5

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: Redistributing EIGRP using route-map Nexus 5596 L3

It is listed in the link in my first post:

http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/unicast/5_0_3_N1_1/l3_rpm.html#wp1088438

If you read the route-map section, it states that prefix-list is used for match based on an address or range of addresses. And ACL is used for a number of IP packet fields such as the following:

- Source or destination IPv4 address

- Protocol

- Precedence

- ToS

Can you tell me which bug you are waiting for 5.1(3)?

Regards,

jerry

5 REPLIES
Cisco Employee

Redistributing EIGRP using route-map Nexus 5596 L3

You cannot use IP access-list inside a route-map to perform redistribution in NXOS. You will have to use prefix-list instead:

http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/unicast/5_0_3_N1_1/l3_rpm.html#wp1071167

However, N5500 NXOS 5.1(3)N1(1) has an IP prefix-list bug which the ip prefix-list command is not available in the CLI (I cannot share the bug ID since it is still internal), you should downgrade it to NXOS 5.0(3)N2(2b) instead.

HTH,

jerry

New Member

Redistributing EIGRP using route-map Nexus 5596 L3

First of all thanks for your reply. Very much appreciated.

I have been waiting for 5.1(3)N1(1)  for 2 months now for a bug fix.

It is hard to fallback. Is this documented somewhere that I cannot use IP ACL for routemap to do redist?

Thanks

Cisco Employee

Re: Redistributing EIGRP using route-map Nexus 5596 L3

It is listed in the link in my first post:

http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/unicast/5_0_3_N1_1/l3_rpm.html#wp1088438

If you read the route-map section, it states that prefix-list is used for match based on an address or range of addresses. And ACL is used for a number of IP packet fields such as the following:

- Source or destination IPv4 address

- Protocol

- Precedence

- ToS

Can you tell me which bug you are waiting for 5.1(3)?

Regards,

jerry

New Member

Redistributing EIGRP using route-map Nexus 5596 L3

thanks. The bug was the management SVI which is now a new feature in the new code.

Cisco Employee

Re: Redistributing EIGRP using route-map Nexus 5596 L3

Thanks for the info and points.

Regards,

jerry

1951
Views
0
Helpful
5
Replies
CreatePlease login to create content