Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Redundant Sup Engines on a 4510

Hi, I'm trying to design a network that uses a 4510 with redundant sups in the data center, and a couple of 3560Es as distribution switches that lead to access layer switches. I'd like to split the load on the 2 3560s by running MST and having each working under normal conditions and have the ability to take over the other switch's load in the event one of those 3560s goes down. These 3560s will each have 2 10gb uplinks, and I was wondering if I can use the 2 10gb uplinks on each of the sup 6E engines, even the redundant one to support an uplink from an active 3560 switch. In other words I'd like to have each 3560 use its 10gb uplink interfaces in an etherchannel that runs down to one of the sup engine's 10gb uplinks. Then I would have the other 3560 doing the same thing to redundant sup engine. Will that work, are those uplinks on a redundant sup active even though the sup engine is not the active sup engine?

thank you,

Bill

2 ACCEPTED SOLUTIONS

Accepted Solutions
Hall of Fame Super Silver

Re: Redundant Sup Engines on a 4510

Hello Bill,

we are using one link on each supervisor.

this is an access layer switch.

I can see the CDP neighbors on link te3/1 and te4/1.

Hope to help

Giuseppe

Cisco Employee

Re: Redundant Sup Engines on a 4510

Starting IOS 12.2.48 with Sup6-E in a redundant config, all 4 10G uplinks are available in 2:1 oversubscribed mode.

The command to enable the 4 10GE ports is:

hw-module uplink mode shared-backplane

regards,

-amit singh

6 REPLIES
Hall of Fame Super Silver

Re: Redundant Sup Engines on a 4510

Hello Bill,

we have recently deployed C4500 with double supervisor:

the 10GE link on standby supervisor can be used see the following:

Mod Redundancy role Operating mode Redundancy status

----+-------------------+-------------------+----------------------------------

3 Active Supervisor SSO Active

4 Standby Supervisor SSO Standby hot

sh ip int br | inc Ten

TenGigabitEthernet3/1 unassigned YES unset up up

TenGigabitEthernet3/2 unassigned YES unset administratively down down

TenGigabitEthernet4/1 unassigned YES unset up up

TenGigabitEthernet4/2 unassigned YES unset administratively down down

We are using

sh ver | inc image

System image file is "bootflash:cat4500-ipbasek9-mz.122-50.SG1.bin"

Hope to help

Giuseppe

New Member

Re: Redundant Sup Engines on a 4510

Thanks Giuseppe, so it looks like from your output they are available, but you yourself are not actually using them. Hopefully I can get this in a lab and test for sure. Thanks for the insight.

Hall of Fame Super Silver

Re: Redundant Sup Engines on a 4510

Hello Bill,

we are using one link on each supervisor.

this is an access layer switch.

I can see the CDP neighbors on link te3/1 and te4/1.

Hope to help

Giuseppe

New Member

Re: Redundant Sup Engines on a 4510

Oh, I see, great. Thank you.

Cisco Employee

Re: Redundant Sup Engines on a 4510

Starting IOS 12.2.48 with Sup6-E in a redundant config, all 4 10G uplinks are available in 2:1 oversubscribed mode.

The command to enable the 4 10GE ports is:

hw-module uplink mode shared-backplane

regards,

-amit singh

New Member

Re: Redundant Sup Engines on a 4510

thank you amit

421
Views
4
Helpful
6
Replies