Hi Expert,
I found below messages on SLOT 2 (WS-x6524-100FX-MM). What does it mean? Would it be hardware error on SLOT 2?
Thanks
remote command switch show plat hard asicreg titan
ERRORS:
0x8 : TI_MX_SM_ERR_STAT_MASK = 3FFF
0x67 : TI_SV_DONT_TAKE_PKT_CNT = 4
0x177: TI_SC_BAD_PAYLOAD_CRC = 1 ERRORS:
0x8 : TI_MX_SM_ERR_STAT_MASK = 3FFF
0x67 : TI_SV_DONT_TAKE_PKT_CNT = 4
0x177: TI_SC_BAD_PAYLOAD_CRC = 1
remote command switch show plat hard asicreg PENTAMAK slot 2 port 1 error-counters print-non-zero ---
PENTAMAK 2/1
0180: PK_TS_S_TOCT = 01BE
PENTAMAK 2/1
0181: PK_TS_S_TTOT = 0004
PENTAMAK 2/1
0182: PK_TS_S_T64 = 0001
PENTAMAK 2/1
0183: PK_TS_S_T127 = 0001
PENTAMAK 2/1
0184: PK_TS_S_T255 = 0002
PENTAMAK 2/1
0192: PK_TS_S_MCAST = 0004
PENTAMAK 2/1
0193: PK_TS_S_ISL1Q = 0003
remote command switch show plat hard asicreg QCHIP slot 2 port 1 error-counters print-non-zero ---
QCHIP device 1
0018: _Q_PF1_CBL_DROP_CNT_15_0 = 30F7
--- remote command switch show plat hard asicreg RCHIP slot 2 port 1 error-counters print-non-zero ---
RCHIP device 1
0074: _R_NIC_PDROP_15_0 = FFFF
RCHIP device 1
0076: _R_NIC_MDROP_15_0 = 0030
remote command switch show plat hard asicreg SCULPTOR slot 2 port 1 error-counters print-non-zero ---
SCULPTOR 2/1
0071: SP_CC_S_HI_PKT_CNT_LO = 19D3
SCULPTOR 2/1
0073: SP_CC_S_LO_PKT_CNT_LO = FFFF
SCULPTOR 2/1
0095: SP_TW_S_NEG_PLD_ERR_CNT = FFFF
SCULPTOR 2/1
00B6: SP_RI_S_PKT_CNT_LO = FFFF
SCULPTOR 2/1
014A: SP_TI_S_PKT_CNT_LO = FFFF
SCULPTOR 2/1
01EC: 5B0D
SCULPTOR 2/1
01EE: FFFF
remote command switch show plat hard asicreg SCULPTOR slot 2 port 1 error-counters print-non-zero ---
SCULPTOR 2/1
0071: SP_CC_S_HI_PKT_CNT_LO = 19D3
SCULPTOR 2/1
0073: SP_CC_S_LO_PKT_CNT_LO = FFFF
SCULPTOR 2/1
0095: SP_TW_S_NEG_PLD_ERR_CNT = FFFF
SCULPTOR 2/1
00B6: SP_RI_S_PKT_CNT_LO = FFFF
SCULPTOR 2/1
014A: SP_TI_S_PKT_CNT_LO = FFFF
SCULPTOR 2/1
01EC: 5B0D
SCULPTOR 2/1
01EE: FFFF
