Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Router 3600

Hi Everybody.

when start my router 3600 across the console , it show the next content

It´s normal this POST?

The running of the router is normal, although It loss the comnunication 2 or 3 times per week , , but after  I restart, It´s running correct.

I have seen that Smart Init is enabled, ....and It show the memory positions...

Thanks Community

Main memory is configured to 64 bit mode with parity disabled

program load complete, entry point: 0x80008000, size: 0x864e20

Self decompressing the image : #################################################

######################################## [OK]

Smart Init is enabled

smart init is sizing iomem

  ID            MEMORY_REQ                 TYPE

0000DA          0X0004FE00 Single Port Fast Ethernet

0000D6          0X000D8A10 FE Port Module, 2 WAN

0000D6          0X000D8A10 FE Port Module, 2 WAN

                0X00280000 OIR memory

                0X000F3BB0 public buffer pools

                0X00211000 public particle pools

TOTAL:          0X00785DD0

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 8Mb.

Using 12 percent iomem. [8Mb/64Mb]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3660-I-M), Version 12.3(2)T1,  RELEASE SOFTWARE (fc2)

Synched to technology version 12.3(1.9)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Fri 22-Aug-03 23:31 by dchih

Image text-base: 0x600089B8, data-base: 0x60DA0000

cisco 3660 (R527x) processor (revision 1.0) with 57344K/8192K bytes of memory.

Processor board ID JHY0735K1JQ

R527x CPU at 225Mhz, Implementation 40, Rev 10.0, 2048KB L2 Cache

Channelized E1, Version 1.0.

Bridging software.

X.25 software, Version 3.0.0.

Primary Rate ISDN software, Version 1.1.

3660 Chassis type: ENTERPRISE

1 FastEthernet/IEEE 802.3 interface(s)

6 Channelized E1/PRI port(s)

DRAM configuration is 64 bits wide with parity disabled.

125K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Press RETURN to get started!

3 REPLIES

Router 3600

Hi, this output is normal. No problems are shown.

I suggest you to upgrade IOS with a fresh release, e.g. 12.4.

Regards.

New Member

Router 3600

Thanks Dadiele,

Could you to recomend for me some tools for verify the stress of routers?

Best regards

Router 3600

How do you mean 'the stress'?

113
Views
0
Helpful
3
Replies