Hi i have a problem with a Catalys 6509-E, it was worrking normal but i dont know what happen and have this messgaes currently in console of supervisor that field...
Initializing ATA monitor library...
Self extracting the image... [OK]
Self decompressing the image : ################################################################################################### [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) s72033_sp Software (s72033_sp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF8, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Sat 03-Mar-07 00:56 by tinhuang
Image text-base: 0x40101040, data-base: 0x41458000
00:00:04: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:04: %PFREDUN-6-STANDBY: Initializing as STANDBY processor
00:00:05: %SYS-SP-STDBY-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:04: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
Firmware compiled 20-Feb-07 14:12 by integ Build [100]
00:00:05: %OIR-SP-STDBY-6-CONSOLE: Changing console ownership to route processor
System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2005 by cisco Systems, Inc.
00:00:12: %SYS-SP-STDBY-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
00:00:12: %SYS-SP-STDBY-3-LOGGER_FLUSHED: System was paused for 00:00:03 to ensure console debugging output.
00:00:12: %OIR-SP-STDBY-6-CONSOLE: Changing console ownership to switch processor
*** System received a Software forced crash ***
signal= 0x17, code= 0x24, context= 0x42321d34
PC = 0x402cfaac, Cause = 0x1820, Status Reg = 0x34008002
System Bootstrap, Version 8.4(2) Release
Copyright (c) 1994-2005 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 524288 Kbytes of main memory
Autoboot executing command: "boot bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXF8.bin"
Loading image, please wait ...
And when i connected in other supervisor, the console show this:
CK6509_4C_4#sh redundancy
Redundant System Information :
------------------------------
Available system uptime = 3 years, 7 weeks, 6 days, 33 minutes
Switchovers system experienced = 3
Standby failures = 711
Last switchover reason = active unit failed
Hardware Mode = Simplex
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
-------------------------------
Active Location = slot 6
Current Software state = ACTIVE
Uptime in current state = 18 hours, 37 minutes
Image Version = Cisco Internetwork Operating System Software
IOS (tm) s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF8, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.
Compiled Sat 03-Mar-07 00:49 by tinhuang
BOOT = sup-bootdisk:s72033-ipservicesk9_wan-mz.122-18.SXF8.bin,1;
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer (slot: unavailable) information is not available because it is in 'DISABLED' state
CK6509_4C_4#
Oct 14 16:49:38: %PFREDUN-SP-6-ACTIVE: Standby processor removed or reloaded, changing to Simplex mode
Oct 14 16:51:12: %PFREDUN-SP-6-ACTIVE: Standby processor removed or reloaded, changing to Simplex mode
Oct 14 16:52:47: %PFREDUN-SP-6-ACTIVE: Standby processor removed or reloaded, changing to Simplex mode
I have configurate the redundandy the next type...
CK6509_4C_4#
!
redundancy
mode sso
main-cpu
auto-sync running-config
!
CK6509_4C_4#sh mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
5 0 Supervisor-Other Unknown Unknown
6 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL10467QHQ
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
5 0000.0000.0000 to 0000.0000.0000 0.0 Unknown Unknown Unknown
6 0016.9df6.b42c to 0016.9df6.b42f 5.2 8.4(2) 12.2(18)SXF8 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
5 Policy Feature Card 3 WS-F6K-PFC3B SAL1045726H 2.3 Other
6 Policy Feature Card 3 WS-F6K-PFC3B SAL10457BQX 2.3 Ok
6 MSFC3 Daughterboard WS-SUP720 SAL10456T9P 2.5 Ok
Mod Online Diag Status
---- -------------------
5 Unknown
6 Pass
My question is:
With the reset or module of Supervisor engine 720 (module 5) fix the problem???
The is is wrong and i have to upgrade the IOS????
What is the processing of upgrade the IOS??
I have to change the Supervisor engine 720???
Well thank you...
Best Regards
