cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
633
Views
0
Helpful
3
Replies

seek help:I meet a question about 6509

sunxia.vip
Level 1
Level 1

After the 6509 Switch starts,enters directly rommon.Below is the detailed information

Router>en

Router#show ip inter b

Interface IP-Address OK? Method Status Protocol

Vlan1 unassigned YES unset administratively down down

GigabitEthernet1/1 unassigned YES unset administratively down down

GigabitEthernet1/2 unassigned YES unset administratively down down

GigabitEthernet4/1 unassigned YES unset administratively down down

GigabitEthernet4/2 unassigned YES unset administratively down down

GigabitEthernet4/3 unassigned YES unset administratively down down

GigabitEthernet4/4 unassigned YES unset administratively down down

GigabitEthernet4/5 unassigned YES unset administratively down down

GigabitEthernet4/6 unassigned YES unset administratively down down

GigabitEthernet4/7 unassigned YES unset administratively down down

GigabitEthernet4/8 unassigned YES unset administratively down down

Router#

00:01:28: %ONLINE-SP-6-INITFAIL: Module 1: Failed to synchronize Port asic

Router#

Router#host 6509A

00:02:13: %ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event

00:02:13: %C6KPWR-SP-4-DISABLED: power to module in slot 4 set off (Reset)

Router#confi t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#host cisco6509A

Config mode locked out until standby initializes

Router(config)#

%Software-forced reload

3 Replies 3

sunxia.vip
Level 1
Level 1

Breakpoint exception, CPU signal 23, PC = 0x40299B44

-Traceback= 40299B44 40297C98 4036B8B4 4036B8E4 40401740 4035BA24 4035BA80 4032DFC0 4032EE60 402E1FC4 402DF758 402DF9CC 4029DD1C

$0 : 00000000, AT : 418E0000, v0 : 41D00000, v1 : 00000010

a0 : 41CF3FB0, a1 : FFFFFFFC, a2 : 00000010, a3 : 00000315

t0 : 00000001, t1 : 0000003B, t2 : 50006CA0, t3 : 00000001

t4 : 00000352, t5 : 00000000, t6 : 50006C98, t7 : 003BAF63

s0 : 00000000, s1 : 00000000, s2 : 50329290, s3 : 50329290

s4 : 085ACBFA, s5 : 00000040, s6 : 00009000, s7 : 0000005A

t8 : 0000838A, t9 : 00000000, k0 : 00000000, k1 : 00000000

gp : 418ED8A0, sp : 50006CF0, s8 : 00000000, ra : 40297C98

EPC : 40299B44, ErrorEPC : 0D4CF57B, SREG : 3401F103

MDLO : 99999A5F, MDHI : 00000315, BadVaddr : C1A2A916

CacheErr : E4800000, DErrAddr0 : 1E02000C, DErrAddr1 : 80006B88

Cause 00000024 (Code 0x9): Breakpoint exception

Writing crashinfo to bootflash:crashinfo_20090429-162634

=== Flushing messages (16:26:34 UTC Wed Apr 29 2009) ===

Buffered messages:

00:00:42: RP: Currently running ROMMON from S (Gold) region

00:00:49: %SYS-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) c6sup2_rp Software (c6sup2_rp-PS-M), Version 12.1(27b)E1, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Thu 12-Oct-06 21:49 by hqluong

00:00:49: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start

00:00:49: %SYS-6-BOOTTIME: Time taken to reboot after reload = 14886108 seconds

00:00:48: %SYS-SP-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) c6sup1_sp Software (c6sup1_sp-SP-M), Version 12.1(27b)E1, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Thu 12-Oct-06 22:26 by hqluong

00:00:50: %C6KENV-SP-4-FANVERCHK: Power-supply 1 inserted is only compatible with Version 1 fan-tray. Please make sure fan is low-output fan-tray

00:00:50: %OIR-SP-6-INSPS: Power supply inserted in slot 1

00:00:50: %C6KPWR-SP-4-PSOK: power supply 1 turned on.

00:00:50: %C6KENV-SP-4-FANVERCHK: Power-supply 2 inserted is only compatible with Version 1 fan-tray. Please make sure fan is low-output fan-tray

00:00:50: %OIR-SP-6-INSPS: Power supply inserted in slot 2

00:01:28: %ONLINE-SP-6-INITFAIL: Module 1: Failed to synchronize Port asic

00:02:13: %ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event

00:02:13: %C6KPWR-SP-4-DISABLED: power to module in slot 4 set off (Reset)

Queued messages:

00:02:31: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debuggin

00:02:30: %SYS-SP-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.

00:02:31: %OIR-SP-6-CONSOLE: Changing console ownership to switch processor

*** System received a Software forced crash ***

signal= 0x17, code= 0x24, context= 0x618fc684

PC = 0x6012fe38, Cause = 0x1820, Status Reg = 0x34018002

System Bootstrap, Version 5.3(1)

Copyright (c) 1994-1999 by cisco Systems, Inc.

c6k_sup1 processor with 65536 Kbytes of main memory

rommon 1 >

rommon 1 >

rommon 1 > exit

monitor: command "exit" not found

rommon 2 >

00:00:09: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor

00:00:10: %OIR-6-CONSOLE: Changing console ownership to route processor

System Bootstrap, Version 12.1(3r)E2, RELEASE SOFTWARE (fc1)

Copyright (c) 2000 by cisco Systems, Inc.

Cat6k-MSFC2 platform with 262144 Kbytes of main memory

rommon 2 >

rommon 2 >

rommon 2 >

System Bootstrap, Version 5.3(1)

Copyright (c) 1994-1999 by cisco Systems, Inc.

c6k_sup1 processor with 65536 Kbytes of main memory

rommon 1 >

rommon 1 >

rommon 2 > boot

Self decompressing the image : ############################################################################################################################################################### [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

Leo Laohoo
Hall of Fame
Hall of Fame

You need raise a TAC RMA request. Here's the reason why:

00:02:13: %ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event

00:02:13: %C6KPWR-SP-4-DISABLED: power to module in slot 4 set off (Reset)

It's due to the "timer event".

Hope this helps.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco