06-24-2014 01:16 AM - edited 03-07-2019 07:49 PM
Hello guys,
I have a question about why one port on a Nexus 7000 with a N7K-M132XP-12 (32 port 10G card) doesn't show any values
when looking at "show inter e 9/27 transceiver details", all values are just zero.
N7K# show inter e 9/27 transceiver details
Ethernet9/27
transceiver is present
type is 10Gbase-SR
name is CISCO-EXCELIGHT
part number is SPP5101SR-C1
revision is A
serial number is EXX13050136
nominal bitrate is 10300 MBit/sec
Link length supported for 50/125um OM2 fiber is 82 m
Link length supported for 62.5/125um fiber is 26 m
Link length supported for 50/125um OM3 fiber is 300 m
cisco id is --
cisco extended id number is 4
number of lanes 1
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------
Current Alarms Warnings
Measurement High Low High Low
----------------------------------------------------------------------------
Temperature N/A 0.00 C 0.00 C 0.00 C 0.00 C
Voltage N/A 0.00 V 0.00 V 0.00 V 0.00 V
Current N/A 0.00 mA 0.00 mA 0.00 mA 0.00 mA
Tx Power N/A 0.00 dBm 0.00 dBm 0.00 dBm 0.00 dBm
Rx Power N/A 0.00 dBm 0.00 dBm 0.00 dBm 0.00 dBm
Transmit Fault Count = 2
----------------------------------------------------------------------------
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
Tried to remove the SFT+ and inserted a new, but same results, all values are 0.
Does anyone know why it doesn't show any values?
We are runing version 6.2(8)
And here's the port configuration:
interface Ethernet9/27
switchport
switchport mode trunk
spanning-tree port type edge trunk
05-12-2020 07:15 AM
Hello everyone,
I have the same issue on a Nexus7700 running system version: 8.3(2) with a N77-F324FQ-25 10/40 Gbps Ethernet Module, Hardware revision 1.1
All counters are at zero.
Ethernet1/2
transceiver is present
type is QSFP-40GE-LR4
name is CISCO-FINISAR
part number is FTL4C1QL1C-C3
revision is A
serial number is FNS22491735
nominal bitrate is 10300 MBit/sec per channel
Link length supported for 9/125um fiber is 2 km
cisco id is --
cisco extended id number is 208
cisco part number is 10-3063-02
cisco product id is WSP-Q40GLR4L
cisco vendor id is V02
number of lanes 4
Lane Number:1 Network Lane
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------
Current Alarms Warnings
Measurement High Low High Low
----------------------------------------------------------------------------
Temperature N/A 0.00 C 0.00 C 0.00 C 0.00 C
Voltage N/A 0.00 V 0.00 V 0.00 V 0.00 V
Current N/A 0.00 mA 0.00 mA 0.00 mA 0.00 mA
Tx Power N/A 0.00 dBm 0.00 dBm 0.00 dBm 0.00 dBm
Rx Power N/A 0.00 dBm 0.00 dBm 0.00 dBm 0.00 dBm
Transmit Fault Count = 0
----------------------------------------------------------------------------
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
Lane Number:2 Network Lane
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------
Current Alarms Warnings
Measurement High Low High Low
----------------------------------------------------------------------------
Temperature N/A 0.00 C 0.00 C 0.00 C 0.00 C
Voltage N/A 0.00 V 0.00 V 0.00 V 0.00 V
Current N/A 0.00 mA 0.00 mA 0.00 mA 0.00 mA
Tx Power N/A 0.00 dBm 0.00 dBm 0.00 dBm 0.00 dBm
Rx Power N/A 0.00 dBm 0.00 dBm 0.00 dBm 0.00 dBm
Transmit Fault Count = 0
----------------------------------------------------------------------------
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
Lane Number:3 Network Lane
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------
Current Alarms Warnings
Measurement High Low High Low
----------------------------------------------------------------------------
Temperature N/A 0.00 C 0.00 C 0.00 C 0.00 C
Voltage N/A 0.00 V 0.00 V 0.00 V 0.00 V
Current N/A 0.00 mA 0.00 mA 0.00 mA 0.00 mA
Tx Power N/A 0.00 dBm 0.00 dBm 0.00 dBm 0.00 dBm
Rx Power N/A 0.00 dBm 0.00 dBm 0.00 dBm 0.00 dBm
Transmit Fault Count = 0
----------------------------------------------------------------------------
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
Lane Number:4 Network Lane
SFP Detail Diagnostics Information (internal calibration)
----------------------------------------------------------------------------
Current Alarms Warnings
Measurement High Low High Low
----------------------------------------------------------------------------
Temperature N/A 0.00 C 0.00 C 0.00 C 0.00 C
Voltage N/A 0.00 V 0.00 V 0.00 V 0.00 V
Current N/A 0.00 mA 0.00 mA 0.00 mA 0.00 mA
Tx Power N/A 0.00 dBm 0.00 dBm 0.00 dBm 0.00 dBm
Rx Power N/A 0.00 dBm 0.00 dBm 0.00 dBm 0.00 dBm
Transmit Fault Count = 0
----------------------------------------------------------------------------
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
Any suggestions?
Thanks,
Konstantin
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: