Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

SFP validation failed

I am geetting sfp validation failed on a link

 

when I do

 sh interface ethernet 1/19 transceiver details 
Ethernet1/19
    transceiver is present
    type is SFP-1000BASE-T
    name is OEM             
    part number is SFP-T10/100/1000
    revision is 11.0
    serial number is EB1404062678    
    nominal bitrate is 1300 MBit/sec
    Link length supported for copper is 100 m
    cisco id is --
    cisco extended id number is 4

DOM is not supported

 

-----------------------------------------------------------

 

sh interface ethernet 1/19
Ethernet1/19 is down (SFP validation failed)
  Hardware: 1000/10000 Ethernet, address: 547f.eebb.2580 (bia 547f.eebb.2580)
  MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA
  Port mode is access
  auto-duplex, 10 Gb/s, media type is 10G
  Beacon is turned off
  Input flow-control is off, output flow-control is off
  Rate mode is dedicated
  Switchport monitor is off 
  EtherType is 0x8100 
  Last link flapped never
  Last clearing of "show interface" counters 00:06:14
  30 seconds input rate 0 bits/sec, 0 packets/sec
  30 seconds output rate 0 bits/sec, 0 packets/sec
  Load-Interval #2: 5 minute (300 seconds)
    input rate 0 bps, 0 pps; output rate 0 bps, 0 pps
  RX
    0 unicast packets  172 multicast packets  22 broadcast packets
    194 input packets  23236 bytes
    0 jumbo packets  0 storm suppression bytes
    0 runts  0 giants  0 CRC  0 no buffer
    0 input error  0 short frame  0 overrun   0 underrun  0 ignored
    0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop
    0 input with dribble  0 input discard
    0 Rx pause
  TX
    0 unicast packets  0 multicast packets  0 broadcast packets
    0 output packets  0 bytes
    0 jumbo packets
    0 output errors  0 collision  0 deferred  0 late collision
    0 lost carrier  0 no carrier  0 babble 0 output discard
    0 Tx pause
  0 interface resets

 

 

 

 

any idea?

 

2 REPLIES

Have you tried hard coding

Have you tried hard coding the speed on this port to speed 1000?

 

New Member

yes. but it still says linked

yes. but it still says linked not connected

 

# sh interface ethernet 1/19

Ethernet1/19 is down (Link not connected)

  Hardware: 1000/10000 Ethernet, address: 547f.eebb.2580 (bia 547f.eebb.2580)

  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec

  reliability 255/255, txload 1/255, rxload 1/255

  Encapsulation ARPA

  Port mode is access

  auto-duplex, 1000 Mb/s, media type is 10G

  Beacon is turned off

  Input flow-control is off, output flow-control is off

  Rate mode is dedicated

  Switchport monitor is off

  EtherType is 0x8100

  Last link flapped never

  Last clearing of "show interface" counters 00:00:07

  30 seconds input rate 0 bits/sec, 0 packets/sec

  30 seconds output rate 0 bits/sec, 0 packets/sec

  Load-Interval #2: 5 minute (300 seconds)

    input rate 0 bps, 0 pps; output rate 0 bps, 0 pps

  RX

    0 unicast packets  172 multicast packets  22 broadcast packets

    194 input packets  23236 bytes

    0 jumbo packets  0 storm suppression bytes

    0 runts  0 giants  0 CRC  0 no buffer

    0 input error  0 short frame  0 overrun   0 underrun  0 ignored

    0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop

    0 input with dribble  0 input discard

    0 Rx pause

  TX

    0 unicast packets  0 multicast packets  0 broadcast packets

    0 output packets  0 bytes

    0 jumbo packets

    0 output errors  0 collision  0 deferred  0 late collision

    0 lost carrier  0 no carrier  0 babble 0 output discard

    0 Tx pause

  0 interface resets

 

# sh interface ethernet 1/19 status

 

--------------------------------------------------------------------------------

Port          Name               Status    Vlan      Duplex  Speed   Type

--------------------------------------------------------------------------------

Eth1/25       --                 notconnec 160       full    1000    SFP-1000BAS

91
Views
0
Helpful
2
Replies
CreatePlease to create content