Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

show command for ASR 1004

hi all,

is there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device.

i was only able to find 'test interface' but haven't run this yet (currently in production). thanks in advance!

#test interface g ?

  <0-0>     GigabitEthernet interface number

  <0-1000>  GMPLS interface number

  <0-1>     GigabitEthernet interface number

> show interfaces diagnostics optics ge-1/1/2

Physical interface: ge-1/1/2

    Laser bias current                        :  16.576 mA

    Laser output power                        :  1.6770 mW / 2.25 dBm

    Module temperature                        :  44 degrees C / 111 degrees F

    Module voltage                            :  3.1960 V

    Receiver signal average optical power     :  0.8565 mW / -0.67 dBm

    Laser bias current high alarm             :  Off

    Laser bias current low alarm              :  Off

    Laser bias current high warning           :  Off

    Laser bias current low warning            :  Off

    Laser output power high alarm             :  Off

    Laser output power low alarm              :  Off

    Laser output power high warning           :  Off

    Laser output power low warning            :  Off

    Module temperature high alarm             :  Off

    Module temperature low alarm              :  Off

    Module temperature high warning           :  Off

    Module temperature low warning            :  Off

    Module voltage high alarm                 :  Off

    Module voltage low alarm                  :  Off

    Module voltage high warning               :  Off

    Module voltage low warning                :  Off

    Laser rx power high alarm                 :  On

    Laser rx power low alarm                  :  Off

    Laser rx power high warning               :  On

    Laser rx power low warning                :  Off

    Laser bias current high alarm threshold   :  100.000 mA

    Laser bias current low alarm threshold    :  6.000 mA

    Laser bias current high warning threshold :  95.000 mA

    Laser bias current low warning threshold  :  6.498 mA

    Laser output power high alarm threshold   :  5.0120 mW / 7.00 dBm

    Laser output power low alarm threshold    :  0.6300 mW / -2.01 dBm

    Laser output power high warning threshold :  3.9810 mW / 6.00 dBm

    Laser output power low warning threshold  :  0.7940 mW / -1.00 dBm

    Module temperature high alarm threshold   :  85 degrees C / 185 degrees F

    Module temperature low alarm threshold    :  -15 degrees C / 5 degrees F

    Module temperature high warning threshold :  80 degrees C / 176 degrees F

    Module temperature low warning threshold  :  -10 degrees C / 14 degrees F

    Module voltage high alarm threshold       :  3.600 V

    Module voltage low alarm threshold        :  3.000 V

    Module voltage high warning threshold     :  3.499 V

    Module voltage low warning threshold      :  3.099 V

    Laser rx power high alarm threshold       :  0.7943 mW / -1.00 dBm

    Laser rx power low alarm threshold        :  0.0025 mW / -26.02 dBm

    Laser rx power high warning threshold     :  0.6309 mW / -2.00 dBm

    Laser rx power low warning threshold      :  0.0031 mW / -25.09 dBm

Everyone's tags (4)
1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

show command for ASR 1004

Hi John,

There is a command like "show hw-module subslot ... transceiver ... idprom detail" to see port parameters and "show hw-module subslot ... transceiver ... status" to see current status:

Router# show hw-module subslot 4/0 transceiver 2 status 
The Transceiver in slot 4 subslot 0 port 2 is enabled.
  Module temperature                = +41.617 C
  Transceiver Tx supply voltage     = 3292.0 uVolts
  Transceiver Tx bias current       = 4840 uAmps
  Transceiver Tx power              = 349.2 uWatts
  Transceiver Rx optical power      = 0.5 uWatts

Router# show hw-module subslot 4/0 transceiver 5 idprom detail
 
IDPROM for transceiver GigabitEthernet4/0/6:
  Description                               = SFP optics (type 3)
  Transceiver Type:                         = GE SX (19)
  Product Indentifier (PID)                 = FTRJ8519P1BNL-C3
  Vendor Revision                           = A1
  Serial Number (SN)                        = FNS0821K2J5     
  Vendor Name                               = CISCO-FINISAR   
  Vendor OUI (IEEE company ID)              = 00.90.65 (36965)
  CLEI code                                 = CNUIAAMAAA
  Cisco part number                         = 10-1954-01
  Device State                              = Enabled.
  Date code (yy/mm/dd)                      = 04/05/19
  Connector type                            = LC.
  Encoding                                  = 8B10B
                                              NRZ
  Nominal bitrate                           = 2xFC (2100 Mbits/s)
  Minimum bit rate as % of nominal bit rate = not specified
  Maximum bit rate as % of nominal bit rate = not specified
  Link reach for 9u fiber (km)              = SX(550/270m) (0)
                                              1xFC-MM(500/300m) (0)
                                              2xFC-MM(300/150m) (0)
                                              ESCON-MM(2km) (0)
  Link reach for 9u fiber (m)               = SX(550/270m) (0)
                                              1xFC-MM(500/300m) (0)
                                              2xFC-MM(300/150m) (0)
                                              ESCON-MM(2km) (0)
  Link reach for 50u fiber (m)              = 2xFC-MM(300/150m) (30)
  Link reach for 62.5u fiber (m)            = 2xFC-MM(300/150m) (15)
  Nominal laser wavelength                  = 850 nm.
  DWDM wavelength fraction                  = 850.0  nm.
  Supported options                         = Tx disable
                                              Tx fault signal
                                              Loss of signal (standard implementation)
  Supported enhanced options                = Alarms for monitored parameters
  Diagnostic monitoring                     = Digital diagnostics supported
                                              Diagnostics are externally calibrated
                                              Rx power measured is "Averagepower"
  Transceiver temperature operating range   = -5 C to 85 C (extended)
  Minimum operating temperature             = -20 C
  Maximum operating temperature             = 90 C
  High temperature alarm threshold          = +109.000 C
  High temperature warning threshold        = +103.000 C
  Low temperature warning threshold         =  -13.000 C
  Low temperature  alarm threshold          =  -29.000 C
  High voltage alarm threshold              = 3.9000 Volts
  High voltage warning threshold            = 3.7000 Volts
  Low voltage warning threshold             = 2.9000 Volts
  Low voltage alarm threshold               = 2.7000 Volts
  High laser bias current alarm threshold   = 15.000 mAmps
  High laser bias current warning threshold = 12.000 mAmps
  Low laser bias current warning threshold  = 2.000 mAmps
  Low laser bias current alarm threshold    = 1.000 mAmps
  High transmit power alarm threshold       = 0.7424 mWatts
  High transmit power warning threshold     = 0.7424 mWatts
  Low transmit power warning threshold      = 0.959 mWatts
  Low transmit power alarm threshold        = 0.619 mWatts
  High receive power alarm threshold        = 5.9324 mWatts
  High receive power warning threshold      = 3.7416 mWatts
  Low receive power warning threshold       = 0.751 mWatts
  Low receive power alarm threshold         = 0.478 mWatts
  External Calibration constant: Rx power4  = 0.000
  External Calibration constant: Rx power3  = 0.000
  External Calibration constant: Rx power2  = 0.000
  External Calibration constant: Rx power1  = 0.212
  External Calibration constant: Rx power0  = -1.4294966868
  External Calibration: bias current slope  = 1.000
  External Calibration: bias current offset = 0

Kind Regards,
Ivan Shirshin

**Please grade this post if you find it useful.

Kind Regards, Ivan Shirshin **Please grade this post if you find it useful.
6 REPLIES
Cisco Employee

show command for ASR 1004

Hi John,

There is a command like "show hw-module subslot ... transceiver ... idprom detail" to see port parameters and "show hw-module subslot ... transceiver ... status" to see current status:

Router# show hw-module subslot 4/0 transceiver 2 status 
The Transceiver in slot 4 subslot 0 port 2 is enabled.
  Module temperature                = +41.617 C
  Transceiver Tx supply voltage     = 3292.0 uVolts
  Transceiver Tx bias current       = 4840 uAmps
  Transceiver Tx power              = 349.2 uWatts
  Transceiver Rx optical power      = 0.5 uWatts

Router# show hw-module subslot 4/0 transceiver 5 idprom detail
 
IDPROM for transceiver GigabitEthernet4/0/6:
  Description                               = SFP optics (type 3)
  Transceiver Type:                         = GE SX (19)
  Product Indentifier (PID)                 = FTRJ8519P1BNL-C3
  Vendor Revision                           = A1
  Serial Number (SN)                        = FNS0821K2J5     
  Vendor Name                               = CISCO-FINISAR   
  Vendor OUI (IEEE company ID)              = 00.90.65 (36965)
  CLEI code                                 = CNUIAAMAAA
  Cisco part number                         = 10-1954-01
  Device State                              = Enabled.
  Date code (yy/mm/dd)                      = 04/05/19
  Connector type                            = LC.
  Encoding                                  = 8B10B
                                              NRZ
  Nominal bitrate                           = 2xFC (2100 Mbits/s)
  Minimum bit rate as % of nominal bit rate = not specified
  Maximum bit rate as % of nominal bit rate = not specified
  Link reach for 9u fiber (km)              = SX(550/270m) (0)
                                              1xFC-MM(500/300m) (0)
                                              2xFC-MM(300/150m) (0)
                                              ESCON-MM(2km) (0)
  Link reach for 9u fiber (m)               = SX(550/270m) (0)
                                              1xFC-MM(500/300m) (0)
                                              2xFC-MM(300/150m) (0)
                                              ESCON-MM(2km) (0)
  Link reach for 50u fiber (m)              = 2xFC-MM(300/150m) (30)
  Link reach for 62.5u fiber (m)            = 2xFC-MM(300/150m) (15)
  Nominal laser wavelength                  = 850 nm.
  DWDM wavelength fraction                  = 850.0  nm.
  Supported options                         = Tx disable
                                              Tx fault signal
                                              Loss of signal (standard implementation)
  Supported enhanced options                = Alarms for monitored parameters
  Diagnostic monitoring                     = Digital diagnostics supported
                                              Diagnostics are externally calibrated
                                              Rx power measured is "Averagepower"
  Transceiver temperature operating range   = -5 C to 85 C (extended)
  Minimum operating temperature             = -20 C
  Maximum operating temperature             = 90 C
  High temperature alarm threshold          = +109.000 C
  High temperature warning threshold        = +103.000 C
  Low temperature warning threshold         =  -13.000 C
  Low temperature  alarm threshold          =  -29.000 C
  High voltage alarm threshold              = 3.9000 Volts
  High voltage warning threshold            = 3.7000 Volts
  Low voltage warning threshold             = 2.9000 Volts
  Low voltage alarm threshold               = 2.7000 Volts
  High laser bias current alarm threshold   = 15.000 mAmps
  High laser bias current warning threshold = 12.000 mAmps
  Low laser bias current warning threshold  = 2.000 mAmps
  Low laser bias current alarm threshold    = 1.000 mAmps
  High transmit power alarm threshold       = 0.7424 mWatts
  High transmit power warning threshold     = 0.7424 mWatts
  Low transmit power warning threshold      = 0.959 mWatts
  Low transmit power alarm threshold        = 0.619 mWatts
  High receive power alarm threshold        = 5.9324 mWatts
  High receive power warning threshold      = 3.7416 mWatts
  Low receive power warning threshold       = 0.751 mWatts
  Low receive power alarm threshold         = 0.478 mWatts
  External Calibration constant: Rx power4  = 0.000
  External Calibration constant: Rx power3  = 0.000
  External Calibration constant: Rx power2  = 0.000
  External Calibration constant: Rx power1  = 0.212
  External Calibration constant: Rx power0  = -1.4294966868
  External Calibration: bias current slope  = 1.000
  External Calibration: bias current offset = 0

Kind Regards,
Ivan Shirshin

**Please grade this post if you find it useful.

Kind Regards, Ivan Shirshin **Please grade this post if you find it useful.

show command for ASR 1004

ivan,

you're awesome! thanks!

i tried googling for CLI commands for ASR but only gave me specs. would highly appreciate if you could give me a link?

>sh hw-module subslot 0/0 transceiver 4 status

The Transceiver in slot 0 subslot 0 port 4 is enabled.

  Module temperature                        = +32.437 C

  Transceiver Tx supply voltage             = 3271.0 mVolts

  Transceiver Tx bias current               = 28796 uAmps

  Transceiver Tx power                      =  2.9 dBm

  Transceiver Rx optical power              = -26.6 dBm

>sh hw-module subslot 0/0 transceiver 4 idprom detail

IDPROM for transceiver GigabitEthernet0/0/4:

  Description                               = SFP optics (type 3)

  Transceiver Type:                         = GE ZX (23)

Cisco Employee

show command for ASR 1004

thanks a lot!

Cisco Employee

show command for ASR 1004

Welcome and thanks for ratings!

Kind Regards, Ivan Shirshin **Please grade this post if you find it useful.
New Member

Hello guys,

Hello guys,

there is a way to enable log on ASR 1000 for transceiver problem about TX/RX power?

i can see the values of TX RX by the command : sh hw-module subslot 0/0 transceiver xxx....., but if i have a problem the device doesn't reply any logs....

thks,

Ale

12686
Views
20
Helpful
6
Replies
CreatePlease login to create content