Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

show platform port-asic - 6500

On a 3750 you can do a show platform port-asic stats drop command.  Is there a corresponding command for 6500 chassis?

thanks

6 REPLIES
Cisco Employee

show platform port-asic - 6500

Hello Brain,

Try this,

remote command switch show platform hardware asicreg pinnacle slot x port y error-counters print-all

Let me know if this helps.

Thanks,

Richard.

New Member

show platform port-asic - 6500

Richard,

If I try this on a line card (ws-x6724-sfp), I get not supported.  If i use it on a sup, it gives a bunch of pinnacle information, but not any errors.   What I'm looking for is the errors/discards reported by the hw, vs what you see in software counters, as those can be inaccurate.

Thanks

Brian

Cisco Employee

show platform port-asic - 6500

Hello Brain,

Can you please post the output of sh mod and sh ver and the module/port you are trying to look for errors?

Thanks,

Richard.

New Member

show platform port-asic - 6500

lhdccore1#show mod
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
  1    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      SAL09475U9L
  2    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      SAD08160CKG
  3   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL09243AR6
  4   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL092229PL
  5    2  Supervisor Engine 720 (Active)         WS-SUP720-BASE     SAL09528QS6
  6    2  Supervisor Engine 720 (Hot)            WS-SUP720-BASE     SAL09475K8C
  7   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL1052CESL
  8   24  CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL1206F8PX
  9    1  Application Control Engine Module      ACE10-6500-K9      SAD111101GA

Mod MAC addresses                       Hw    Fw           Sw           Status
--- ---------------------------------- ------ ------------ ------------ -------
  1  0015.f928.2d40 to 0015.f928.2d43   2.2   12.2(14r)S5  12.2(18)SXF7 Ok
  2  000f.908a.bc6c to 000f.908a.bc6f   1.5   12.2(14r)S5  12.2(18)SXF7 Ok
  3  0014.a8e5.3fa0 to 0014.a8e5.3fb7   2.2   12.2(14r)S5  12.2(18)SXF7 Ok
  4  0014.694c.bb80 to 0014.694c.bb97   2.2   12.2(14r)S5  12.2(18)SXF7 Ok
  5  0013.c346.b358 to 0013.c346.b35b   3.3   8.1(3)       12.2(18)SXF7 Ok
  6  0014.a97e.400c to 0014.a97e.400f   3.3   8.1(3)       12.2(18)SXF7 Ok
  7  0019.5606.f120 to 0019.5606.f137   2.5   12.2(14r)S5  12.2(18)SXF7 Ok
  8  001e.f7c9.3ca4 to 001e.f7c9.3cbb   3.1   12.2(18r)S1  12.2(18)SXF7 Ok
  9  001b.2a65.588c to 001b.2a65.5893   1.4   8.7(0.22)ACE A2(3.1)      Ok

Mod  Sub-Module                  Model              Serial       Hw     Status
---- --------------------------- ------------------ ----------- ------- -------
  1  Distributed Forwarding Card WS-F6700-DFC3A     SAL09486Q7V  2.5    Ok
  2  Distributed Forwarding Card WS-F6700-DFC3A     SAD081708F5  2.2    Ok
  3  Distributed Forwarding Card WS-F6700-DFC3A     SAL08321V6C  2.2    Ok
  4  Distributed Forwarding Card WS-F6700-DFC3A     SAL0848695L  2.2    Ok
  5  Policy Feature Card 3       WS-F6K-PFC3A       SAL09528R7H  2.5    Ok
  5  MSFC3 Daughterboard         WS-SUP720          SAL09528SCS  2.5    Ok
  6  Policy Feature Card 3       WS-F6K-PFC3A       SAL095186BZ  2.5    Ok
  6  MSFC3 Daughterboard         WS-SUP720          SAL095184SF  2.5    Ok
  7  Distributed Forwarding Card WS-F6700-DFC3A     SAL1102DKAE  2.5    Ok
  8  Distributed Forwarding Card WS-F6700-DFC3A     SAL1102DKBY  2.5    Ok


lhdccore1#show ver
Cisco Internetwork Operating System Software
IOS (tm) s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Thu 23-Nov-06 06:00 by kellythw
Image text-base: 0x40101040, data-base: 0x42D98000

ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
BOOTLDR: s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF7, RELEASE SOFTWARE (fc1)

lhdccore1 uptime is 4 years, 50 weeks, 10 hours, 28 minutes
Time since lhdccore1 switched to active is 4 years, 50 weeks, 10 hours, 38 minutes
System returned to ROM by Stateful Switchover (SP by power on)
System restarted at 22:25:04 CST Thu Mar 15 2007
System image file is "disk0:s72033-advipservicesk9_wan-mz.122-18.SXF7.bin"


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco WS-C6509-E (R7000) processor (revision 1.2) with 458720K/65536K bytes of memory.
Processor board ID SMG0951N5A8
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from power-on
SuperLAT software (copyright 1990 by Meridian Technology Corp).
X.25 software, Version 3.0.0.
Bridging software.
TN3270 Emulation software.
29 Virtual Ethernet/IEEE 802.3 interfaces
104 Gigabit Ethernet/IEEE 802.3 interfaces
5 Ten Gigabit Ethernet/IEEE 802.3 interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.

65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102

sample of show int count err:

   Port        Align-Err    FCS-Err   Xmit-Err    Rcv-Err UnderSize OutDiscards
Gi7/17              0          0          0          0         0           0
Gi7/18              0          0          0          0         0           0
Gi7/19              0          0          0          0         0          16
Gi7/20              0          0          0          0         0          16
Gi7/21              0          0          0          0         0           0
Gi7/22              0          0          0          0         0           0
Gi7/23              0          0          0          0         0           0
Gi7/24              0          0          0          0         0           0
Gi8/1               0          0          0          0         0           0
Gi8/2               0          0          0          0         0           0
Gi8/3               0          0          0          0         0           0
Gi8/4               0          0          0          0         0           0
Gi8/5               0          0          0          0         0           0
Gi8/6               0          0          0          0         0     1170954
Gi8/7               0          0          0          0         0       18031
Gi8/8               0          0          0          0         0        4358
Gi8/9               0          0          0          0         0      368254
Gi8/10              0          0          0          0         0           0
Gi8/11              0          0          0          0         0           0
Gi8/12              0          0          0          0         0           0
Gi8/13              0          0          0          0         0           0
Gi8/14              0          0          0          0         0           0
Gi8/15              0          0          0          0         0         251
Gi8/16              0          0          0          0         0           0
Gi8/17              0          0          0          0         0           0
Gi8/18              0          0          0          0         0           0
Gi8/19              0          0          0          0         0      154857
Gi8/20              0          0          0          0         0        1377
Gi8/21              0          0          0          0         0          

lhdccore1#show int g8/19

GigabitEthernet8/19 is up, line protocol is up (connected)

  Hardware is C6k 1000Mb 802.3, address is 001e.f7c9.3cb6 (bia 001e.f7c9.3cb6)

  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,

     reliability 255/255, txload 139/255, rxload 32/255

  Encapsulation ARPA, loopback not set

  Keepalive set (10 sec)

  Full-duplex, 1000Mb/s, media type is T

  input flow-control is on, output flow-control is on

  Clock mode is auto

  ARP type: ARPA, ARP Timeout 04:00:00

  Last input never, output 00:00:25, output hang never

  Last clearing of "show interface" counters 3d21h

  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 155600

  Queueing strategy: fifo

  Output queue: 0/40 (size/max)

  5 minute input rate 127167000 bits/sec, 13144 packets/sec

  5 minute output rate 545734000 bits/sec, 46785 packets/sec

     918181884 packets input, 1075634236367 bytes, 0 no buffer

     Received 0 broadcasts (0 multicasts)

     0 runts, 0 giants, 0 throttles

     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

     0 watchdog, 0 multicast, 0 pause input

     0 input packets with dribble condition detected

     3509140493 packets output, 5109379770302 bytes, 0 underruns

     0 output errors, 0 collisions, 0 interface resets

     0 babbles, 0 late collision, 0 deferred

     0 lost carrier, 0 no carrier, 0 PAUSE output

     0 output buffer failures, 0 output buffers swapped out lhdccore1#show int g8/19

Troubleshooting why we are getting all these discards (all related to a VMWare/SAN issue).  I want to make sure they are valid, as I know the counters can report back false results.. although when I've looked at the same traffic going through a 3750, sw and hw are reporting back the same, so I have no reason to suspect the 6500's aren't as well.

Cisco Employee

show platform port-asic - 6500

Hello Brain,

Instead of applying that in the SP try applying the same command which i have given earlier in DFC line card

remote login module X

show platform hardware asicreg pinnacle slot x port y error-counters print-non-zero

Let me know if this helps.

Thanks,

Richard

New Member

show platform port-asic - 6500

Closer;  But no matter what slot I select, it module in slot:  is not present

lhdccore1-dfc8#show platform hardware asicreg pinnacle slot ?

  <1-13>  slot number

lhdccore1-dfc8#$show platform hardware asicreg pinnacle slot 8 port 19 print-non-zero
The module in slot: 8 is not present

4236
Views
10
Helpful
6
Replies
CreatePlease login to create content