Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

SIP-400/SPA-2X1GE-V2, mls qos trust dscp command not available?

hi,

I'm testing a spa-2x1ge-v2 plugged into a sip-400 in a 7609. I've got qos enabled globally. When I go into my gig interface and try to turn on 'mls qos trust dscp' the command just isn't there. Is it called something else for this SIP/SPA combo? I'm getting worried because when I do 'sh mls qos' I see no qos counters for the SIP-400. I expected to see counters like I see when I have a SIP-600/SPA-10X1GE-V2 connected. (I'm running c7600s72033-adventerprisek9-mz.122-33.SRB3.bin)

Any ideas?

thanks,

Andy

4 REPLIES
Hall of Fame Super Silver

Re: SIP-400/SPA-2X1GE-V2, mls qos trust dscp command not availab

Hello Andy,

the different behaviour could be derived from the different characteristics of SIP400 and SIP600.

If I remember correctly from one presentation on the inside of C7600: SIP600 hosts a DFC while SIP400 hasn't this DFC on board

download the following pdf about SIP and SPA

http://tools.cisco.com/search/display?url=http%3A%2F%2Fwww.cisco.com%2Fen%2FUS%2Fdocs%2Finterfaces_modules%2Fshared_port_adapters%2Fconfiguration%2F6500series%2F65spasw.pdf&pos=5&strqueryid=10&websessionid=wQG67B8J2BnwwB77MoFY6RT

Hope to help

Giuseppe

Cisco Employee

Re: SIP-400/SPA-2X1GE-V2, mls qos trust dscp command not availab

Hi Andy,

The SPA-2x1GE-V2 is a WAN card, you should use the interface level command "service-policy" to apply a QoS policy, and the "policy map" to configure QoS policy.

Please see attach link:

http://www.cisco.com/en/US/products/hw/routers/ps368/module_installation_and_configuration_guides_chapter09186a0080440138.html#wp1162382

Here is the MQC config guideline:

http://www.cisco.com/en/US/products/hw/routers/ps368/module_installation_and_configuration_guides_chapter09186a0080440138.html#wp1297330

HTH,

jerry

Silver

Re: SIP-400/SPA-2X1GE-V2, mls qos trust dscp command not availab

Hello Andrew!

Both Giuseppe and Jerry are right. On Flexwan, SIP-400 and SIP-200 you have to apply Qos using a service policy and the MLS qos commands wouldnot be available. SIP-600 is an exception as it has a DFC and the supervisor-tables (fwd tables) residing on it. So to some extent SIP-600 is different from the other WAN cards and shows support for many LAN-card-like features.

Also to note that "trust ip dscp" would not be required on a WAN card like sip-400 because the dscp/cos trust is enabled by default on the WAN cards. The wan cards wouldnot re-write the markings on the packet.

Hope this helps.

Regards,

Niranjan

(Pls rate helpful posts)

New Member

Re: SIP-400/SPA-2X1GE-V2, mls qos trust dscp command not availab

hi Niranjan,

thanks! This answers my question. I was not aware that the sip-400 would trust DSCP by default.

Thanks to everyone else who responded with useful links & information also.

bye,

Andy

887
Views
0
Helpful
4
Replies