Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

SNMP OID for Inline Power Measurement

Does anybody know of an OID to measure the inlinepower of a card (I specifically want to get the readout from the below marked in bold):

#sh powe       

Load for five secs: 2%/5%; one minute: 2%; five minutes: 2%

Time source is NTP, 07:14:05.157 UTC Fri Sep 27 2013

system power redundancy mode = redundant

system power total =     3795.12 Watts (90.36 Amps @ 42V)

system power used =      1144.92 Watts (27.26 Amps @ 42V)

system power available = 2650.20 Watts (63.10 Amps @ 42V)

                        Power-Capacity PS-Fan Output Oper

PS   Type               Watts   A @42V Status Status State

---- ------------------ ------- ------ ------ ------ -----

1    WS-CAC-4000W-INT   3795.12 90.36  OK     OK     on

2    WS-CAC-4000W-INT   3795.12 90.36  OK     OK     on

                        Pwr-Allocated  Oper

Fan  Type               Watts   A @42V State

---- ------------------ ------- ------ -----

1    WS-C6509-E-FAN      150.36  3.58  OK

                        Pwr-Requested  Pwr-Allocated  Admin Oper

Slot Card-Type          Watts   A @42V Watts   A @42V State State

---- ------------------ ------- ------ ------- ------ ----- -----

1    WS-X6148A-45AF       49.56  1.18    49.56  1.18  on    on

3    WS-X6148A-45AF       49.56  1.18    49.56  1.18  on    on

5    WS-SUP32-GE-3B      154.98  3.69   154.98  3.69  on    on

6    WS-SUP32-GE-3B      154.98  3.69   154.98  3.69  on    on

8    WS-X6148A-45AF       49.56  1.18    49.56  1.18  on    on

                        Inline         Inline         Inline         Inline

                        Pwr-Requested  Pwr-Allocated  Local-Pwr-Pool Power

Slot Card-Type          Watts   A @42V Watts   A @42V Watts   A @42V Status

---- ------------------ ------- ------ ------- ------ ------- ------ ----------

1    WS-F6K-48-AF        113.40  2.70   127.40  3.03    34.61  0.82  On        

3    WS-F6K-48-AF        144.90  3.45   162.79  3.88    34.61  0.82  On                     <<<---------- this bit

8    WS-F6K-48-AF        126.00  3.00   141.56  3.37    34.61  0.82  On        

on a 6500 running old code.

#sh ver

Load for five secs: 2%/6%; one minute: 1%; five minutes: 2%

Time source is NTP, 07:19:15.425 UTC Fri Sep 27 2013

Cisco IOS Software, s3223_rp Software (s3223_rp-IPSERVICESK9_WAN-VM), Version 12.2(33)SXH5, RELEASE SOFTWARE (fc1)

Thanks,

Ian

1 ACCEPTED SOLUTION

Accepted Solutions

SNMP OID for Inline Power Measurement

Try the POWER-ETHERNET-MIB.

Please rate replies and mark question as "answered" if applicable.

Please rate replies and mark question as "answered" if applicable.
2 REPLIES

SNMP OID for Inline Power Measurement

Try the POWER-ETHERNET-MIB.

Please rate replies and mark question as "answered" if applicable.

Please rate replies and mark question as "answered" if applicable.

SNMP OID for Inline Power Measurement

Thanks for the pointer.

Found the ones I'm after now

SNMPv2-SMI::mib-2.105.1.3.1.1.4.1 = Gauge32: 113

SNMPv2-SMI::mib-2.105.1.3.1.1.4.3 = Gauge32: 144

SNMPv2-SMI::mib-2.105.1.3.1.1.4.8 = Gauge32: 125

354
Views
0
Helpful
2
Replies