10-24-2013 01:33 AM - edited 03-07-2019 04:12 PM
Hi,
We have a nexus 7000 setup with several fexes connected to it.
In Cisco docs I can read that it is possible to configure a fex port as span source but not as destination.
You can configure the host interfaces on the Fabric Extender as Switched Port Analyzer (SPAN) sourceports. Fabric Extender ports cannot be configured as a SPAN destination. Only one SPAN session is supported for all the host interfaces on the same Fabric Extender. Ingress source (Rx), egress source(Tx), or both monitoring is supported.
However when I am trying to configure the source port of a fex. I receive the error below. I don't find any info about this error.
"ERROR: Eth150/1/38: Cannot add FEX ports connected through Ricard/Rouen "
Did anyone have this issue before?
Thanks,
Joris
Solved! Go to Solution.
11-05-2013 09:01 AM
Hi Joris,
SPAN source functionality on satellite ports and host interface port channels is not supported when the FEX is connected to F2 Series modules. Beginning with Cisco NX-OS Release 6.2(2), FEX ports are supported as an egress SPAN source on F2e Series modules.
Nexus7k# show module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
1 0 Supervisor module N7K-SUP2 active *
3 48 1/10 Gbps Ethernet Module N7K-F248XP-25 ok
Mod Sw Hw
--- -------------- ------
1 6.x(x) 1.0
3 6.x(x) 1.1
Mod MAC-Address(es) Serial-Num
--- -------------------------------------- ----------
1 84-xx-xxx to 84-xx-xxxx JAxxxxxxxx
3 00-xxx to 00-xxxxx JAxxxxxxx
Mod Online Diag Status
--- ------------------
1 Pass
3 Pass
* this terminal session
Regards
Jens
11-05-2013 09:01 AM
Hi Joris,
SPAN source functionality on satellite ports and host interface port channels is not supported when the FEX is connected to F2 Series modules. Beginning with Cisco NX-OS Release 6.2(2), FEX ports are supported as an egress SPAN source on F2e Series modules.
Nexus7k# show module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
1 0 Supervisor module N7K-SUP2 active *
3 48 1/10 Gbps Ethernet Module N7K-F248XP-25 ok
Mod Sw Hw
--- -------------- ------
1 6.x(x) 1.0
3 6.x(x) 1.1
Mod MAC-Address(es) Serial-Num
--- -------------------------------------- ----------
1 84-xx-xxx to 84-xx-xxxx JAxxxxxxxx
3 00-xxx to 00-xxxxx JAxxxxxxx
Mod Online Diag Status
--- ------------------
1 Pass
3 Pass
* this terminal session
Regards
Jens
11-21-2013 07:38 AM
Thanks Jens,
The fexes are indeed connected to a F2 card on the Nexus 7k.
It is supported from NX-OS version 6.2.2, but only on F2e cards. So I think it will never be supported on F2 cards.
too bad,
best Regards,
Joris
02-20-2014 01:04 AM
Hi All,
I did find a possible workaround, but haven't tested it yet. Create a SPAN session with filter.
Best Regards,
Joris
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide