Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Spanning VLANs - Multiple Sites

We are opening a new office that is roughly 20km from another core site. We plan on provisioning 2 x DS3 between sites and likely have a requirement to support the same subnets (VLANs) at both locations. Let?s say we have our core site (SA1) and new site (SA2). Core infra will be at SA1 (WAN, Inet, Servers, etc).

SA1 has 2 x 6513?s running HSRP and VTP load balancing ? core of the LAN. Has anyone spanned VLAN?s across sites like this and know of any major concerns to watch out for in doing so? One concern is delays from L3 lookups to the remote MSFC?s ? MLS should help here for any cached routes/decisions.

5 REPLIES
New Member

Re: Spanning VLANs - Multiple Sites

We are currently doing what you are talking about for some developers that need to see certain Layer 2 data @ our company but from the west coast to the east coast of the US with latency of 76ms and higher without any complaints.

L2TPv3 works great for this setup. Just requires advanced ip 12.4.10 and higher on the routers.

I haven't seen any issues and the tunnels have been up for over 6-7 months.

New Member

Re: Spanning VLANs - Multiple Sites

thanks for the info, it helps, we are planning to span approx 40 vlans with 450 users at new site. Is your setup is similar to what I mentioned and if you can provide some more details around actual implementation it would be great.

New Member

Re: Spanning VLANs - Multiple Sites

6509

trunking to router

7204

trunking on gi0/0

L2TPv3 Configuration

!

pseudowire-class vlan-xconnect

encapsulation l2tpv3

ip local interface Loopback1

ip pmtu

ip tos reflect

!

interface Loopback1

description L2TPv3 Tunnel Source

ip address 10.5.240.1 255.255.255.255

!

interface FastEthernet0/1.95

description L2TPv3 Tunnel VLAN 95

encapsulation dot1Q 95

no cdp enable

xconnect 10.5.240.3 95 pw-class vlan-xconnect

!!!!!!!

3845

trunking on gi0/0

L2TPv3 Configuration

!

pseudowire-class vlan-xconnect

encapsulation l2tpv3

ip local interface Loopback1

ip pmtu

ip tos reflect

!

interface Loopback1

description L2TPv3 Tunnel Source

ip address 10.5.240.3 255.255.255.255

!

interface FastEthernet0/1.95

description L2TPv3 Tunnel VLAN 95

encapsulation dot1Q 95

no cdp enable

xconnect 10.5.240.1 95 pw-class vlan-xconnect

http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/120newft/120limit/120s/120s23/l2tpv3.htm

You can either use GRE or L2TPv3, GRE seems a better fit for you than L2TPv3.

GRE is easier to configure also.

http://www.cisco.com/en/US/tech/tk827/tk369/tk287/tsd_technology_support_sub-protocol_home.html

New Member

Re: Spanning VLANs - Multiple Sites

Can you explain how to use gre for l2 trunking? I did not know this was possible other than using bridging.

New Member

Re: Spanning VLANs - Multiple Sites

Wouldn't simple BCP configuration achieve what you want to do?

1088
Views
0
Helpful
5
Replies
CreatePlease to create content