Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

SPT Inconsistent Native Vlan

Hi,

I cant figure out why this is showing on switches.

Core switch brc-k25-1 is using Native Vlan 1

Access switch c2-k25-5 is using Native Vlan 1

I get the following error message on the access switch:

Jun 27 08:57:40: %SPANTREE-2-RECV_PVID_ERR: Received BPDU with inconsistent peer vlan id 171 on GigabitEthernet1/0/49 VLAN1.
Jun 27 08:57:40: %SPANTREE-2-BLOCK_PVID_PEER: Blocking GigabitEthernet1/0/49 on VLAN0171. Inconsistent peer vlan.
Jun 27 08:57:40: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking GigabitEthernet1/0/49 on VLAN0001. Inconsistent local vlan.
Jun 27 08:57:40: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Jun 27 08:57:55: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking GigabitEthernet1/0/49 on VLAN0171. Port consistency restored.
Jun 27 08:57:55: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking GigabitEthernet1/0/49 on VLAN0001. Port consistency restored.
Jun 27 08:57:55: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up

Because of the error, I cannot login to the access switch using the native Vlan IP Address.

 

brc-k25-1 config:

interface GigabitEthernet3/2

 description c2-k25-5
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 1,146,171
 switchport mode trunk
 logging event link-status
 logging event trunk-status
 qos trust dscp
 tx-queue 1
   bandwidth percent 69
 tx-queue 2
   bandwidth percent 1
 tx-queue 3
   bandwidth percent 15
   priority high
 tx-queue 4
   bandwidth percent 15
end

brc-k25-1#sh interfaces gigabitEthernet 3/2 switchport
Name: Gi3/2
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Administrative Native VLAN tagging: enabled
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk associations: none
Administrative private-vlan trunk mappings: none
Operational private-vlan: none
Trunking VLANs Enabled: 1,146,171
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL

interface Vlan1
 ip address 172.27.40.254 255.255.255.02
 ip access-group vlan1out out

==================================================

c2-k25-5 config:

c2-k25-5#sh cdp ne
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
                  D - Remote, C - CVTA, M - Two-port Mac Relay

Device ID        Local Intrfce     Holdtme    Capability  Platform  Port ID
brc-k25-1        Gig 1/0/49        138             R S I  WS-C4506  Gig 3/2

interface GigabitEthernet1/0/49
 description brc-k25-5
 switchport trunk allowed vlan 1,146,171
 switchport mode trunk

interface Vlan1
 ip address 172.27.40.18 255.255.255.0
!
interface Vlan146
 ip address 172.31.146.1 255.255.255.0

c2-k25-5#sh interfaces gigabitEthernet 1/0/49 switchport
Name: Gi1/0/49
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Administrative Native VLAN tagging: enabled
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk Native VLAN tagging: enabled
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk associations: none
Administrative private-vlan trunk mappings: none
Operational private-vlan: none
Trunking VLANs Enabled: 1,146,171
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Protected: false
Unknown unicast blocked: disabled
Unknown multicast blocked: disabled
Appliance trust: none

Everyone's tags (1)
3 REPLIES
Purple

  If you are using vlan 1 as

  If you are using vlan 1 as the native vlan it really doesn't need to be in the trunk allowed statement , try removing vlan 1 from the allowed vlans and see what happens.

New Member

Thanks for the replies.I did

Thanks for the replies.

I did remove the ACL from the VLAN1 but nothing change. Also the allowed VLAN1 was not included in the trunk allowed before, same result as now.

 

Jun 30 09:06:40: %SPANTREE-2-RECV_PVID_ERR: Received BPDU with inconsistent peer vlan id 171 on GigabitEthernet1/0/49 VLAN1.

Jun 30 09:06:40: %SPANTREE-2-BLOCK_PVID_PEER: Blocking GigabitEthernet1/0/49 on VLAN0171. Inconsistent peer vlan.
Jun 30 09:06:40: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking GigabitEthernet1/0/49 on VLAN0001. Inconsistent local vlan.
Jun 30 09:06:41: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Jun 30 09:06:55: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking GigabitEthernet1/0/49 on VLAN0171. Port consistency restored.
Jun 30 09:06:55: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking GigabitEthernet1/0/49 on VLAN0001. Port consistency restored.
Jun 30 09:06:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up

 

We have multiple switches attached to the brc-k25-1 and only 2 switches are affected using VLAN1 management. I had to create another VLAN ID so that I can use that IP Address to SSH. Very weird problem.

 

Hello interface Vlan1 ip

Hello

 

interface Vlan1
 ip address 172.27.40.254 255.255.255.02
 ip access-group vlan1out out

What are you filtering here coming into vlan 1?

res

Paul

Please don't forget to rate any posts that have been helpful. Thanks.
331
Views
0
Helpful
3
Replies
CreatePlease to create content