Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

STP problem ?

Hi NetPro,

anyone knows why these msgs keep promping from my access switch ?

1d10h: add static addr 0100.5e01.0203, port Gi0/1 (8) vlan 72

1d10h: add static addr 0100.5e01.0203, port Gi0/2 (8) vlan 72

1d10h: add static addr 0100.5e01.0203, port Gi0/1 (8) vlan 72

1d10h: add static addr 0100.5e01.0203, port Gi0/2 (8) vlan 72

1d10h: add static addr 0100.5e01.0203, port Gi0/1 (8) vlan 72

1d10h: add static addr 0100.5e01.0203, port Gi0/2 (8) vlan 72

1d10h: add static addr 0100.5e01.0203, port Gi0/1 (8) vlan 72

1d10h: add static addr 0100.5e01.0203, port Gi0/2 (8) vlan 72

1d10h: Add address 00e0.8602.1e76, on port Gi0/1 vlan 303

1d10h: Add address 00e0.8602.1e77, on port Gi0/1 vlan 303

1d10h: Add address 00e0.8602.1e75, on port Gi0/1 vlan 303

1d10h: Add address 00e0.8602.1e78, on port Gi0/1 vlan 303

1d10h: Add address 00e0.8602.1e8a, on port Gi0/1 vlan 303

1d10h: Add address 0020.f5f0.0100, on port Gi0/1 vlan 300

your reply will be highly appreciated.

regards,

Jack

3 ACCEPTED SOLUTIONS

Accepted Solutions
Hall of Fame Super Bronze

Re: STP problem ?

Are you using port-security?

Can we see the configuration from this switch?

__

Edison.

Cisco Employee

Re: STP problem ?

Hi Jack,

I believe this is not something critical. Looks like your log settings might have been configured with logging level for the console, monitor, and buffer logging as "Debugging" in this way, every single action the switches take such as the normal port adress learning is reported into the log.

If you see from your logs this is just that some end statiocn might have some online and their mac addresses are learned on ports and your previous message it is a multicast mac address which is getting learned on port and vlan.

Can you please check the "sh logs" and see what is the level it is configured for? and if it is debugging you can change it accordingly as per your network requirement.

HTH

Ankur

*Pls rate all helpfull post

Hall of Fame Super Bronze

Re: STP problem ?

Do you have any debugging turned on?

What you are seeing is a normal behavior when the switch is populating its CAM table, however this output shouldn't be seen in the log.

Type show debug and see if there is anything turned on. To disable debug, type undebug all

HTH,

__

Edison.

5 REPLIES
Hall of Fame Super Bronze

Re: STP problem ?

Are you using port-security?

Can we see the configuration from this switch?

__

Edison.

New Member

Re: STP problem ?

Hi Edison,

Thanks for the fast responsed, well this is Cat3500XL. i didnt apply Port Security.

attached with the switch config.

thanks.

regards,

Jack

Hall of Fame Super Bronze

Re: STP problem ?

Do you have any debugging turned on?

What you are seeing is a normal behavior when the switch is populating its CAM table, however this output shouldn't be seen in the log.

Type show debug and see if there is anything turned on. To disable debug, type undebug all

HTH,

__

Edison.

Cisco Employee

Re: STP problem ?

Hi Jack,

I believe this is not something critical. Looks like your log settings might have been configured with logging level for the console, monitor, and buffer logging as "Debugging" in this way, every single action the switches take such as the normal port adress learning is reported into the log.

If you see from your logs this is just that some end statiocn might have some online and their mac addresses are learned on ports and your previous message it is a multicast mac address which is getting learned on port and vlan.

Can you please check the "sh logs" and see what is the level it is configured for? and if it is debugging you can change it accordingly as per your network requirement.

HTH

Ankur

*Pls rate all helpfull post

New Member

Re: STP problem ?

Hi Edison and Ankur,

thanks for the information. you were right it's caused by logging buffer and monitor setting.

thanks.

regards,

Jack

110
Views
0
Helpful
5
Replies